Regency HZ33CE-LP10 Скачать руководство пользователя страница 38

Страница: 38 / 56

Regency HZ33CE-10 Gas Fireplace

installation

OPTIONAL REFLECTIVE PANEL INSTALLATION

Remove the mesh barrier and flush glass door (see instructions in

manual) remove firebox base tray

by removing 6 screws in the locations

shown below.

Diagram 2

Diagram 3

Back Panel

Diagram 5

Diagram 4

Diagram 6

Place the top panel in first, secure with 4 screws.

(See Diagram 2 for screw locations)

With the top panel in place - install back panel. The back panel fits

under the top panel, push the top panel up to fit back panel into

position. (Diagram 3)

The side panels are installed last, slide in as shown in Diagram 5.

Note:

The bend in the metal on the side panels should face inward

(toward the wall of the firebox - see

Diagram 5

). If the side panels

have been installed incorrectly the firebox base will not fit.

Reinstall the firebox base and glass door.

Before installation, panels must be handled and cleaned as per instructions noted below:

Black Enamel Panels

•

Black Enamel panels must be inspected for scratches and dimples prior to installation. All claims to be recorded at this time. Claims

for damage after installation will not receive consideration.

•

Black Enamel panels will discolor a little during normal operation.

This is normal and should not be considered a defect.

All hand and finger marks

MUST

be cleaned off with a soft cloth. Use an ammonia based cleaner (ie. glass cleaner) to remove any

fingerprints before applying heat to the unit.

Failure to do this will result in burn stain on panels which you will be unable to remove.

Not protected by product warranty.

Completed Panel Installation

Note: Diagram is shown without a burner.

Diagram 1: Remove the 6 screws - lift out base tray

. Remove 4 screws prior to top panel installation.

Do not remove this panel.

Secure back panel with panel bracket as shown below. This bracket

will come with the appliance and is enclosed in manual package.

Содержание HZ33CE-LP10

























































Результаты поиска

Содержание HZ33CE-LP10

Отзывы:

Похожие инструкции для HZ33CE-LP10

Бренды по названию

Популярные бренды

Regency HZ33CE-LP10, Инструкция для владельца и по установке

Результаты поиска

Содержание HZ33CE-LP10

Отзывы:

Похожие инструкции для HZ33CE-LP10

Бренды по названию

Популярные бренды