Regency HZ33CE-LP10 Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 56

background image

Regency HZ33CE-10 Gas Fireplace

|

39

|

39

installation

GLASS CRYSTALS AND OPTIONAL STONES

INSTALLATION ON BURNER AND FIREBOX FLOOR

Glass Crystals shown on Burner and Firebox Floor

BURNER PACKAGES

Unit

*Glass Crystals **Spa Stones

Volcanic Stones

Beads

HZ33CE

4 lb

4 lb glass + 70 spa stones 4 lb glass + 30 stones

5lbs

NOTE:

*

Glass Crystals are available in 1lb and 5lb bags.

** Spa stone package contains 70 stones

Spread the Glass Crystals or Stones evenly over the burner. Ensure the crystals (or stones) do not overlap too much as this will effect the flame pattern.
IMPORTANT NOTE:
Only the supplied approved Glass Crystals and Stones are to be used with these fireplaces. Use of any other type of glass crystals or stones can alter the
unit's performance, any damage caused by the use of any unapproved glass or stones will not be covered under warranty.

When using Ceramic Spa/Volcanic Stones ensure required glass crystals/beads are used as a base. DO NOT overstack Ceramic Spa stones or Volcanic

stones on the burner or in the pilot area.

1) Start installing Crystals on back of

Burner and Firebox Floor

2) Distribute Crystals evenly towards

front of Burner and Firebox Floor

3) Work Crystals from back to front

edge of Firebox Floor

4)

Spread

Crystals

evenly over the

burner and firebox base

5) Ensure Crystals

DO NOT

block the

front of the pilot hood and flame to

light the burner

OPTIONAL SPA STONES INSTALLATION (AROUND BURNER

)

NOTE:

Spa/Volcanic stones are

NOT

to be placed anywhere on the burner tube or Pilot assembly area.

NOTE:

Correct final glass installation of Crystals shown

in step 4 and 5.

The Burner and Firebox Floor should not be visible

when the flame is out.

«
...
37
38
39
40
41
...
»

Содержание HZ33CE-LP10

























































Отзывы:

Нет отзывов

Похожие инструкции для HZ33CE-LP10

Бренд: Magiglo Страницы: 52

Бренд: Valor Страницы: 26

Бренд: Archgard Страницы: 56

Бренд: Majestic Страницы: 64

Бренд: Landmann Страницы: 2

Бренд: Paramount Fitness Страницы: 14

Бренд: Archgard Страницы: 26

Ecosmart Fire BK Series

Бренд: MAD Страницы: 14

Бренд: Vermont Castings Страницы: 14

Бренд: ADURO Страницы: 99

Бренд: Canvas Страницы: 100

Jensen Geneva 1581LP

Бренд: KSP Страницы: 51

ARISTOCRAT V36EC2

Бренд: Vanguard Страницы: 8

Бренд: Mainstays Страницы: 76

Бренд: Majestic Страницы: 70

Бренд: Heat&Glo Страницы: 42

STRATFORD SI38DV

Бренд: Lexington Forge Страницы: 40

Бренд: Outdoor Lifestyles Страницы: 43

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды