20
|
Regency
®
U38-10 ULTIMATE Freestanding Gas Stove
|
20
operating instructions
FIRST FIRE
The first fire in your stove is part of the paint curing
process. To ensure that the paint is properly cured,
it is recommended that you burn your fireplace
for at least four (4) hours the first time you use
it with the fan on. When first operated, the unit
will release an odour caused by the curing of the
paint, the burning off of any oils remaining from
manufacturing. Smoke detectors in the house may
go off at this time. Open a few windows to ventilate
the room for a couple of hours.
The glass panel may require cleaning after the
unit has cooled down.
DO NOT ATTEMPT TO CLEAN THE
GLASS WHILE IT IS HOT.
Note: When the glass is cold and the appliance
is lit, it may cause condensation and fog
the glass. This condensation is normal
and will disappear in a few minutes as
the glass heats up.
OPERATING
INSTRUCTIONS
1)
Read and understand these instructions before
operating this appliance.
2)
Check to see that all wiring is correct and
enclosed to prevent possible shock.
3)
Check to ensure there are no gas leaks.
4)
Make sure the glass in the door frame is
properly positioned. Never operate the
appliance with the glass removed.
5)
Verify that the venting and cap are unobstructed.
6)
Verify log placement. If the pilot cannot be
seen when lighting the unit, the logs have
been incorrectly positioned.
7)
The unit should never be turned off, and on
again without a minimum of a 60 second wait.
During the first few fires, a white film
may develop on the glass front as part
of the curing process. The glass should
be cleaned
or the film will bake on and
become very difficult to remove. Use a
non-abrasive cleaner and NEVER clean
the glass while it is hot.
Proflame
video
DO NOT BURN THE APPLIANCE
WITHOUT THE GLASS FRONT IN
PLACE.
8)
Hook up remote receiver to wire marked 'receiver'
which will be located on the bottom of the appli-
ance. This remote control requires coding. See
remote control instructions for details.
NOTE:
This appliance will operate during power
outages. Only the fan will not operate until
power is restored. If the remote batteries in
both the handheld transmitter or receiver lose
power, the appliance can still be operated by
sliding the switch on the receiver switch from
"Remote" to "ON". To turn on the appliance off
slide the receiver switch from "ON" to "Remote"
or "OFF".
IMPORTANT:
The remote control system sup-
plied with this appliance has several options
for starting/operating the appliance, please
read the remote control operating instructions
(packed with remote control) to understand
how to operate this remote system. You can
download remote functions video with the QR
code below..
LIGHTING
PROCEDURE
Important: If the pilot does not hold, turn pilot knob
to "OFF" position. Wait 5 minutes to clear gas. If
you smell gas - STOP! Follow the safety information
above. If you don't smell gas, repeat Steps 1-6.
1
. Push in gas control knob slightly and turn to
"PILOT" position.
2
. Push in control knob all the way and hold in
until the pilot lights up. Continue to hold the
control knob in for about 20 seconds after the
pilot is lit. Release knob.
3.
Push in gas control knob slightly and turn to
"ON" position.
4
. Ensure the receiver is in the remote position.
IMPORTANT
Prior to igniting or re igniting
the pilot, remove the glass
door.
Set Switch to
Remote
Diagram 1
5
. Press and release the ON/OFF button on the
remote handheld transmitter. An audible beep
should be heard from the receiver.
ON/OFF
Button
6.
The unit will turn on.
SHUTDOWN
PROCEDURE
1
. Press "OFF" on the remote or slide receiver
switch from remote to "OFF".
2
. Turn the gas control knob to the "OFF" position
to turn off the pilot.
Pilot may be shut off during prolonged non use
periods to conserve fuel.
Diagram 2
Remote shown in Manual Mode on Hi