background image

30

 | 

Regency

®

 CLASSIC™ C34-11 Direct Vent Freestanding Gas Stove

 | 

30

installation

 

e)  Cut the 2 ft. or 4 ft. section of rigid pipe 

to length. Ensure that the pipe length 

when cut will seat onto both the starter 

collar and the 90

o

 elbow. 

 Crimped 

section of rigid pipe seats into the 

90

o

 elbow. Only cut the uncrimped 

side of pipe. 

  Dismantle all pipe sections including vent 

terminal.

3.  Attach  the  4"  dia.  flex  liner  to  the  vent 

terminal ensuring that the flex overlaps the 

collar of the vent terminal by a minimum 

of 1-3/8"(35 mm). Use Mill-Pac to seal and 

secure with 3 of the #8 x 1/2" screws (stain

-

less steel). 

 

4.  Attach the adjustable pipe section to the vent 

terminal using Mill-Pac and attach with 3 of 

the #8 x 1/2" screws (stainless steel).

Hint: Apply the sealant (Mill-Pac) to the outer 

pipe before connecting the inner pipe.

Note:  The pipe seam should be facing down.

Note:   To make the installation more aes

-

thetically pleasing, we recommend 

framing out a square that the cap can 

be mounted on.

Note:  If installing termination on a siding 

covered wall, a vinyl siding standoff 

or  furring  strips  must  be  used  to 

ensure  that  the  termination  is  not 

recessed into the siding. For vinyl 

siding standoff installation refer to 

the  Dura-Vent  Termination  instruc

-

tions.

5.  Slide the partially connected pipe and vent 

terminal assembly through the wall thimbles 

(from  the  exterior  into  the  interior)  and 

secure the cap to the exterior wall with 4 of 

the supplied screws (#8 x 1-1/2" drill point, 

stainless steel). Note: pilot holes will need 

to be drilled through the wall thimble on all 

4 corners.

Note:  The  four  screws  provided  for  the 

vent cap should be replaced with ap

-

propriate fasteners for stucco, brick, 

concrete, or other types of sidings.

6.  A bead of non-hardening mastic should 

be run around both the termination and 

vinyl siding standoff to prevent water from 

entering and to make a tight seal between 

the cap and the standoff.

7.  Stretch the 4" dia. flex liner out fully and 

get a trial fit of the liner onto the 4" dia. 

starter collar.

8.  Cut the 4" dia. flex liner to the desired size. 

  Hint: leave an extra 12" to 16" of length, 

this will make the final assembly easier to 

work with.

9.  Secure the 4" dia. flex liner to the 4" adapter 

with Mill-Pac and 3 of the #8 x 1/2" screws 

(stainless steel). 

10  Slide the decorative Thimble Cover over the 

pipe sections and secure with 4 screws (#8 

x 1-1/2" drill point, black) to the wall.

 

Slide the trim collar over the adjustable pipe 

sections to cover the joint of the telescopic 

section.

11. Slide the 90

o

 elbow (crimp end up) and the 

2 ft. or 4 ft. pipe section (crimp end up) 

over the 4" dia. flex liner.

12. Install the spring spacers onto the pipe 

sections.

13. Secure the 4" dia. flex liner with adapter 

onto the stove collar. Put a bead of Mill-Pac 

around the appliance adapter and secure 

with 3 screws (#8 x 1/2, stainless steel).

14.  Attach the pipe section onto the starter collar 

by sealing with Mill-Pac securing with 3 of 

the #8 x 1/2" (black) screws. Pipe seams 

should be facing the wall.

15. Attach the 90

elbow onto the pipe section 

by sealing with Mill-Pac securing with 3 of 

the #8 x 1/2" screws (black).

16. Slide the adjustable pipe section onto the 

90

o

 elbow. The flex may have to be com

-

pressed back in order for the adjustable 

pipe to properly mate to the elbow. Seal  

with Mill-Pac and secure with 3 of the #8 

x 1/2" screws (black). Pipe seams facing 

down.

17. Install the trim collar over the starter collar 

and secure with a #8 x 1/2" screw (black). 

If the pipe needs to be touched up, use only 

Stove  Brite  High  Temperature  Metallic  Black 

Stove Paint.

NOTE: All inner/outer joints must be sealed 

with Mill-Pac. 

Содержание C34 Classic





























































Отзывы: