manualshive.com logo in svg

Reechcraft PowerMAST, Руководство по безопасности оператора, Страница: 39 / 56

Поделиться
Скачать
Reechcraft PowerMAST Скачать руководство пользователя страница 39

reechcraft.com/powermast   888-600-6160

39

Installation of the electrical system should only be carried out by a competent person.  
Incorrectly installing electrical components on the system could lead to personal injury  
or death. Examine the worksite completely, locating any hazards or conditions such as  
standing water, sharp objects, high traffic areas, etc. 

Before installing any electrical cords, be sure all equipment has been thoroughly
examined for proper function and that no cuts, breaks, or damage of any kind exists
with the electrical supply cords or the electrical cords on the drills. If any electrical lines 
are damaged or have excessive wear, discard immediately and use new equipment.

 

The PowerMast system should only be used with electrical power drills that have been 
tested and recommended for use by ReechCraft or your local dealer. (See Table 4.0)

DESCRIPTION

SPECIFICATION

No Load Speed (High Speed for 1/2 Rated Load) 0-1500 RPM (0-3000 RPM)

Output Power

600-700 W (8.5 Amps Minimum)

Input Power

850-1050 W (7.5-9.5 Amps)

Maximum Operating Speed (at 1/2 Rated Load)

0-950 RPM (0-1270 RPM)

Maximum Drill Size

1/2 in. (13 mm)

Collar Size

1.68-1.75 in. (42.5-44.5 mm)

Chuck Type

Keyed Only (Keyless for Setup Only)

Electrical Cord Minimum Rating

15 Amp 12 Gauge Lead

Table 4.0 

- Drill and Electrical Cord Specifications

SECTION 4

POWER SYSTEM INSTALLATION

4.0

  Power System Installation

Содержание PowerMAST

























































Отзывы:

Нет отзывов