manualshive.com logo in svg

Reechcraft PowerMAST, Руководство по безопасности оператора, Страница: 15 / 56

Поделиться
Скачать
Reechcraft PowerMAST Скачать руководство пользователя страница 15

reechcraft.com/powermast   888-600-6160

15

GENERAL SYSTEM INFORMATION

DESCRIPTION

SPECIFICATION

PERFORMANCE

Single Mast System Rated Load 
(Pl Person(s) + Payload)

750 lbs (340 kg)

Twin Mast System Rated Load 
(Pl Person(s) + Payload)

1500 lbs (680 kg)

Maximum Climbing Speed  
(at Rated Load)

25 ft/min (7.6 m/min)

Tie Pull-out Force

Wall-tied System:

 1500 lbs (680 kg) per Tie

Freestanding System:

 N/A

Maximum Allowable Wind Speed 
in Service

Wall-tied System:

 35 mph (15.6 m/s)

Freestanding System (Indoor):

 0 mph (0 m/s)

Freestanding System (Outdoor): 

25 mph (11.2 m/s)

Maximum Allowable Wind  
Speed During Setup

Wall-tied System: 

35 mph (15.6 m/s)

Freestanding System (Outdoor): 

25 mph (11.2 m/s)

DRIVE SYSTEM AND SAFETY FEATURES

Safety Devices

Cam Lever Lock, Overload Clutch,  
and Overspeed Brake

Emergency Lowering

Manual Descent Crank Available

Mast  Connection Type

Interference Locking Cam Lever

Drive System

120:1 Clutch Protected Transmission

Required Voltage

110 VAC Single Phase

Operating System

1/2 in. 8 Amp Minimum Drill Motor

WEIGHTS

Climbing Unit

62 lbs (28.1 kg)

5 ft Mast

32 lbs (14.5 kg)

Tie

7 lbs (3.2 kg)

Platform Support

29 lbs (13 kg)

Maximum System (Single)

Wall-tied System:

 2241 lbs (1016 kg)

Freestanding System (Indoor):

 2061 lbs (935 kg) 

Freestanding System (Outdoor):

 1675 lbs (760 kg) 

DIMENSIONS (L x W x H)

Climbing Unit

12.3 in. x 10.8 in. x 56 in. (312 mm x 274 mm x 1422 mm)

Mast

6 in. x 5 in. x 58 in. (152 mm x 127 mm x 1473 mm)

Platform Support

38.5 in. x 8 in. x 8 in. (978 mm x 203 mm x 203 mm)

Wall-tied System Assembly Stowed

11 in. x 5 in. x 5 in. (278 mm x 127 mm x 127 mm)

Wall-tied System Base

10 in. x 10 in. x 3 in. (254 mm x 254 mm x 76 mm)

1

SECTION 

1

1.5

   Specifications

Table 1.0 

- System Specifications

Содержание PowerMAST

























































Отзывы:

Нет отзывов