manualshive.com logo in svg

Redline Communications RedMAX, Руководство пользователя, Страница: 51 / 55

Поделиться
Скачать
Redline Communications RedMAX Скачать руководство пользователя страница 51

 

 

 Red

MAX

™

 

Subscriber Modem

 

SU-O  User Manual

 

 

70-00057-01-01-DRAFT 

Proprietary Redline Communications © 2007

 September 

7, 

2007 

Page 51 of 55

 

Table 26

:

 Troubleshooting - Event Log Messages 

Log Message 

Description 

SBC Failure - Retries 

Exhausted 

T18 expired beyond the maximum number of allowed 

retries. 

SBC Success [TLV Map: 

XXXXXXXX] 

The subscriber has successfully negotiated its basic 

capabilities with the base station. 

SBC Wait Timeout T18 

[nn retries] 

A SBC request response is not received within 50ms. 

SBC-REQ not sent - no 

BW granted 

base station has not allocated bandwidth to allow 

subscriber to do SBC and registration 

Synchronization 

Completed 

The subscriber has completed scanning for a downlink 

channel, and established synchronization with a base 
station. It will now begin its initial ranging process.  

System startup [status]  
 

The subscriber has begun the bootup sequence. The 

startup status will be included in the text of this message. 
Modes specify a possible reason for reboot. 

TFTP - no response T26 

[nn retries] 

SMC setup has not completed within the allowed time. 

TFTP Completed 

Successfully 

This message confirms that SMC registration has 

completed. Communication with DHCP and ToD servers 
was successful. 

TFTP Success 

SMC IP, ToD, have been successfully obtained via DHCP.

TFTPC failed send 

SMC has failed, and the subscriber will reset the MAC and 

begin registration process again. 

Time-of-day acquired 

Communication with a ToD (RFC-868) server has been 

successful. The correct time of day has been acquired. 

UCD Receiving Timeout 

5 uplink channel descriptors in a row have been expected 

and not received. The subscriber will now restart the 
ranging process in an attempt to re-establish wireless 
synchronization. 

Unicast Initial Ranging 

No Response T3 [nn 
retries] 

The base station has not responded to an initial ranging 

request sent by the subscriber within 200 ms. 

Unicast Initial Ranging 

Retries Exhausted [nn 
retries] 

The subscriber has attempted to perform initial ranging 16 

times and has failed each time. 

Unicast Initial Ranging 

Start [CID: XXXX] 

The subscriber has received a unicast ranging opportunity 

Unicast Ranging Abort 

Indicates that the base station has sent the subscriber a 

ranging abort, telling it to halt the ranging process. 

Uplink Channel 

Parameters Acquired 

The subscriber has successfully obtained the uplink 

channel descriptor 

Uplink SF nn changed 

Changes have been successfully applied to the specified 

uplink service flow. 

Uplink SF nn created 

[CID: XXXX, No.Cls: nn] 

An uplink service flow has been successfully created. 

Uplink SF nn not created 

(no space) [CID: XXXX] 

The subscriber cannot create the specified UL service 

flow, as there is not enough remaining memory. 

 

Содержание RedMAX
























































Отзывы:

Нет отзывов