manualshive.com logo in svg

Redline Communications RedCONNEX AN-80i, Руководство по установке

Поделиться
Скачать
Redline Communications RedCONNEX AN-80i Скачать руководство пользователя страница 35

AN-80i 

Installation Guidelines 

70-00073-01-08-b 

Proprietary Redline Communications © 2011

 

Page 

35

 of 58 

May 27, 2011 

 

Use the following steps to connect the Ethernet cable to the AN-80i unit. 

1. 

Locate the AN-80i Ethernet port and remove the large nut (4), the split rubberized 
gasket (3) and the split washer (2). 

2. 

Thread the Ethernet cable through the large nut (4) and connect the RJ-45 connector 
on the outdoor Ethernet cable (1) to the mating connector on the AN-80i. The RJ-45 
connector is located inside the Ethernet port opening. 

3. 

Fit the split washer (2) over the Ethernet cable (1) and slide tightly against the AN-80i 
chassis. 

 

Important: Weatherproofing the Ethernet Port

 

The split washer must be installed on all AN-80i units having serial numbers beginning 
with 20-2008-00NN-NNNNN.  Beginning with AN-80i series 20-2308-00NN-NNNNN, the split 
washer is not required (may not be included in kit). 

 

 

Figure 23: Weatherproof Ethernet Port - Assembly Drawing 

4. 

Fit the split rubberized gasket (3) over the Ethernet cable (1) and slide tightly against 
the split washer (2). Note that the larger end of the gasket must be towards the end 
of the Ethernet cable. 

5. 

Apply a small amount of grease to weatherproof the nut threads. Replace the nut (4) 
on the threaded portion of the AN-80i chassis. The connector must be finger-tight 
plus 1/8th turn only -- excessive force may damage the connector. 

 

3.3.3

 

Disconnecting the Ethernet Cable 

The RJ-45 connector is recessed within the AN-80i chassis. To disconnect the Ethernet 
cable from the AN-80i, you must  release the locking tab located in the chassis recess. 
Carefully lift the tab to release the RJ-45 connector for removal from the AN-80i. 

 

 

Содержание RedCONNEX AN-80i



























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды