background image

red 

COMPACT 24 BOILER 

USE AND INSTALLATION MANUAL  

Chapter 

page 6 

 

Guarantee conditions - standards 

 

    Technical dept. - All rights reserved - Reproduction prohibited 

 

2. 

GUARANTEE TERMS 

The Manufacturer guarantees the product, with the exception of parts subject to normal wear specified 

below, for 

two years

 from the date of purchase, provided that proof of purchase is supplied in a document 

specifying the name of the retailer and the date the sale was made and that the completed guarantee 

certificate was sent within 8 days of said purchase. The product must also be installed and tested by a 

specialised installer and in accordance with the detailed instructions provided in the instruction manual that 

accompanies the product. 
The guarantee covers the replacement or free repair of parts recognised as being faulty at source due to 

manufacturing defects. 

2.1.  

Warnings 

 

Installation, electrical connection, functional check and maintenance of this appliance must only be 

performed by qualified or authorised personnel. 

 

This appliance must not be used by anyone (including children) with reduced physical, sensory or 

mental skills and with little experience and knowledge, unless they are supervised or have been 

instructed to use the appliance by the person in charge of its safety. 

The guarantee applies, provided that: 

1.

 

The boiler is installed, in accordance with the applicable standards in force and the instructions 

provided in the product use, maintenance and installation manual, by legally qualified personnel 

(Italian Ministerial Decree no. 37 of 22

nd

 January 2008); 

2.

 

The customer holds the documentation certifying its suitability in all parts: 

a.

 

INSTALLATION REPORT - filled in by the installer  

b.

 

TEST REPORT and GUARANTEE APPLICATION - filled in by an authorised serviceman 

3.

 

The guarantee applies from the date of first start-up of the boiler, which must be indicated on the 

boiler manual or from the invoice date. This documentation must be presented to the authorised 

service centre in the event of servicing. 

2.2.  

Exclusions 

The guarantee does not cover any parts found to be faulty due to negligence or inappropriate use, incorrect 

maintenance, or installation not performed in compliance with the manufacturer's instructions. The 

manufacturer will not be held liable for any damage which may - either directly or indirectly - be caused to 

persons, animals or property resulting from failure to observe all the instructions provided in this manual 

and, specifically, concerning the warnings regarding installation, use and maintenance of the appliance. 
The guarantee is not valid if: 

1.

 

The terms for the guarantee application were not observed. 

2.

 

Installation was not performed in observance of the applicable standards in force and the 

instructions provided in the use, maintenance and installation manual. 

The guarantee does not cover: 

1.

 

Damage made by atmospheric agents, chemicals, electrochemical elements, incorrect product use, 

natural disasters, electrical discharges, fires, faults in the electrical system, modifications to or 

tampering with the product, and/or other causes not ensuing from the product manufacturing 

2.

 

Damage caused by normal corrosion  

3.

 

Damage relating to the combustion chamber 

4.

 

Damage to seals, claddings, painted/chromed parts, handles and electrical wires 

5.

 

Damage to masonry work 

6.

 

Damage to parts of the system for the production of DHW not supplied by RED 

7.

 

Damage to the heat exchanger if a suitable condensation-proof circuit is not set up to guarantee a 

minimum boiler return temperature of at least 55 °C. 

Содержание COMPACT 24





























































Отзывы: