RED COMPACT 24 Скачать руководство пользователя

Страница: 41 / 60

red

COMPACT 24 BOILER

Chapter

USE AND MAINTENANCE MANUAL

page

Programming and settings

To store, press the



button to take you to the subsequent

display of “UT 03” to set the minutes.



Setting the MINUTES (abbreviation on the UT 03)

The display

(8)

shows alternately the abbreviation “UT 03” and an

indication of the clock minutes at that moment.
Use the



(increase) or



(decrease) buttons to adjust the

minutes.
To store, press the



button to take you to the subsequent

display of “UT 04”.

The abbreviation “UT 04” is not part of the

PROGRAMMED mode.
It is for the exclusive use of the installer or

authorised technician via restricted access.
Press button 3 again to proceed and display the

abbreviation “UT 05”.

9.4.4.3.

Programme

The COMPACT boiler allows you to set up to 4 operating programmes

spread across the day or an entire week.
Each programme is distinguished by three fundamental steps:



The boiler switch-on time (which must be between

00:00 and 23:40)



The boiler switch-off time (which must be more than

the corresponding switch-on time and be maximum

23:50)



The days on which boiler switch-on and switch-off must

be ON or OFF

Let's analyse

PROGRAMME 1

(summarised in the table below), which

is the first of four programmes in the programming sequence.

PROGRAMME 1

Abbreviation on the

display (8)

UT 05

UT 06

UT 07

Data to enter

Switch-on

Time

Switch-off

Time

Days ON or OFF

On/Off 1,2,3,4,5,6,7

PROGRAMME 1

: setting

the boiler switch-on time.

We are at step

UT 05. The boiler panel display

(8)

alternates the

abbreviation

UT 05 with a time value in hours and minutes. Using the



(increase) or



(decrease) keys, set the boiler

switch-on time

for

this programme. Each time the key is pressed, the time increases or

decreases by 10 minutes. Hold the key down to speed up the increase

or decrease progressively, so that you can make a large modification
quickly. Once the desired time has been set, store it by pressing the



key, which automatically takes you to subsequent step

UT 06.

PROGRAMME 1

: setting

the boiler switch-off time.

We are at step

UT 06. The boiler panel display

(8)

alternates the

abbreviation

UT 06 with a time value in hours and minutes. Using the

Содержание COMPACT 24





























































Результаты поиска

Содержание COMPACT 24

Отзывы:

Похожие инструкции для COMPACT 24

Бренды по названию

Популярные бренды

RED COMPACT 24, Инструкция по использованию и установке

Результаты поиска

Содержание COMPACT 24

Отзывы:

Похожие инструкции для COMPACT 24

Бренды по названию

Популярные бренды