6
REC Installation Manual - REC Solar Panels - IEC
61215
/
61730
Rev L
-
09
.
21
Ref: PM
-
IM
-20
ELECTRICAL INSTALLATION
ELECTRICAL REQUIREMENTS
Application Class
REC solar panels are rated for use in electrical Application Class A, Protection Safety Class II; at hazardous levels of voltage (>
35
V), current(>
8
A)
and power (>
240
W) where general contact access is anticipated (panels qualified for safety through IEC
61730
-
1
and -
2
).
System Requirements
REC solar panels are only for use where they meet the specific technical requirements of the complete system. Ensure other components will not
cause mechanical or electrical damage to the panels. Only panels of the same type and power class should be connected.
String configuration
When connecting panels in a string, plan and execute according to the inverter manufacturer’s instructions. The number of panels connected to an inverter
must not exceed the voltage limits and operating range permi
tt
ed by the manufacturer, nor under any circumstance exceed the maximum system voltage
as stated in the technical specifications for the product at the rear of this manual. The maximum system fuse rating (overcurrent protection rating) and
the maximum reverse current for each panel can be found in the technical specifications for the product at the rear of this manual.
The maximum number of panels in a string can be calculated by dividing the maximum system voltage of the panel by its V
OC
accounting for the lowest
ambient temperature at site, e.g.: for a
1000
V system, if the lowest ambient temperature is
15
°C, the panel has a V
OC
of
40
.
8
V and a temperature coe
ffi
cient
of V
OC
of -
0
.
27%
/°C, the maximum panels per string is
23
(
∆
T°C =
25
° -
15
° =
10
°;
10
° x
0
.
27
=
2
.
7%
;
40
.
8
+
2
.
7%
=
41
.
9
;
1000
V /
40
.
4
=
23
.
9
, so a total
of
23
panels or
974
V). Qualified system designers can make exact calculations that account for specific project requirements and site conditions.
String connection
Panels connected in series must have the same ampere rating. The maximum number of panels that can be connected in series or parallel depends upon
system design, inverter type and environmental conditions. String configuration must correspond to the specifications of other system components e.g.,
inverter. Refer to the reverse current rating of the panel indicated in the technical characteristics at the rear of this manual or on the panel datasheet.
Wiring layout
To minimize voltage surges (e.g., indirect lightning strikes), cables of the same string must be bundled together so loops are as small as possible.
String configurations must be checked before commissioning. If open circuit voltage (V
oc
) and short circuit current (I
sc
) deviate from specification,
this may indicate a configuration fault. Correct DC polarity must be observed at all times.
Electrical Ratings
Electrical ratings are within a specific tolerance of measured values at Standard Test Conditions (STC) as given in the technical characteristics for each
panel at the rear of this manual. Allow for increased panel output as a result of conditions di
ff
erent to STC by multiplying the I
SC
and V
OC
values by a
factor of
1
.
25
(or according to local regulations) when determining component voltage ratings, conductor ampacities, overcurrent device ratings and
size of controls connected to the PV output.
MECHANICAL INSTALLATION
FIRE GUIDELINES
The REC solar panels covered by this manual have a Class C (referencing UL
790
) fire classification. The REC solar panels in
60
-cell format are
rated Type
2
fire classification according to IEC
61730
-
2
:
2016
(ref. ANSI/UL
1703
); The REC solar panels in
72
-cell format are rated Type
1
fire classification according to IEC
61730
-
2
:
2016
(ref. ANSI/UL
1703
). Utilize the following fire safety guidelines when installing REC solar
panels:
• Check with all relevant local authorities for fire safety requirements for any building or structure on to which the panels will be installed,
• The system design must ensure that it can be easily accessed in the event of a building fire,
• Check with relevant authorities for applicable regulations concerning setbacks or other placement restrictions that may apply for roof-
mounted arrays,
• The use of DC ground fault interrupters is recommended. This may also be required by local and national codes,
• All electrical appliances are a fire risk. The panel must be mounted over a fire retardant roof covering rated for the application and a distance
of at least
20
mm (
40
mm for REC solar panels in
72
-cell format) between the panel and the mounting surface, to allow the free circulation
of air beneath the panels at all times.
ORIENTATION
The optimal mounting position of a panel results in the sun’s rays falling perpendicular (i.e., at
90
°) to the surface. To maximize system output, panels
should be installed at the optimum orientation and tilt angle. The specifics of this depend on location and can be calculated by a qualified system
designer. All panels in a string should, wherever possible, have the same orientation and tilt to ensure the system does not underperform due to
mismatched outputs. Dependent on local conditions, a lower angle of installation will potentially increase the requirement for regular cleaning.
DANGER
-
Electrical shock
Safety is paramount when working on the electrical installation. Always follow the electrical requirements to avoid the risk of sparking, fire hazards,
burns and lethal electric shocks
.
NOTE
The IP rating of the junction box provides a level of protection that allows panels to be mounted in any orientation.
i
