REC N-Peak 2 Black Series, Руководство по установке

Страница: 12 / 31

12 REC Installation Manual - REC Solar Panels - IEC 61215 / 61730
Rev L - 09 . 21 Ref: PM - IM -20
CAUTION
The center point of each clamp and the minimum grip length must be fully located in the same clamping zones to be rated to that load (fig. 7 ).
If the panel is secured in zones with di ff erent load values, it is rated to the lowest load value only.
Fig. 7 : Clamping of N-Peak panels on rails parallel to long side of module
MOUNTING REC N - PEAK PANELS WITH CONTINUOUS RAILS PARALLEL TO LONG SIDE OF THE PANEL
A continuous rail (or other support structure) spans the complete underside of the panel.
250 mm [9.8 in]
250 mm [9.8 in]
100 mm [4 in]
100 mm [4 in]
250 mm [9.8 in]
250 mm [9.8 in]
100 mm [4 in]
100 mm [4 in
]
650 mm [25.6 in]
0
0 0
0
0 0
650 mm [25.6 in]
Rail positioning
Rail positioning
Rail position
Rail position
Legend
Clearance Gap
Clamping zone
20-40 mm 40-60 mm > 60 mm < 20 mm
Test Load
(Design Load)
Test Load
(Design Load)
Test Load
(Design Load)
Test Load
(Design Load)
0 - 650 mm
+ 1200 Pa / -1200 Pa *
(+ 800 Pa / -800 Pa)
+ 3000 Pa / -2400 Pa
(+ 2400 Pa / -1600 Pa)
+ 5400 Pa / -2400 Pa
(+ 3600 Pa / -1600 Pa)
X
0 - 100 mm X
+ 1200 Pa / -1200 Pa *
(+ 800 Pa / -800 Pa)
+ 1600 Pa / -1600 Pa *
(+ 1066 Pa / -1066 Pa)
X
100 - 250 mm X
+ 800 Pa / -800 Pa *
(+ 533 Pa / -533 Pa)
+ 2400 Pa / -2400 Pa
(+ 1600 Pa / -1600 Pa)
X
Once a module is secured in each of the 4 zones (fig. 2 ), additional clamps, i.e., ≥5 , may be freely located on panel frame without
a ff ecting the warranty. Loads marked with a
*
were not certified as part of IEC 61215 / 61730 testing; these have been evaluated by
REC’s internal testing process.
Sh
or
t S
id
e
M
ou
nt
in
g
Lo
ng
S
id
e
M
ou
nt
in
g
Legend
Clearance Gap
Clamping zone
20-40 mm 40-60 mm > 60 mm < 20 mm
Test Load
(Design Load)
Test Load
(Design Load)
Test Load
(Design Load)
Test Load
(Design Load)
Rail length under
module
25 - 100 mm
Min.
25 m
m
Ma
x. 100 mm
0 - 208 mm X
+ 1200 Pa / -1200 Pa *
(+ 800 Pa / -800 Pa)
+ 1600 Pa / -1600 Pa *
(+ 1066 Pa / -1066 Pa)
X
208 - 340 mm
+ 1200 Pa / -1200 Pa *
(+ 800 Pa / -800 Pa)
+ 4000 Pa / -2400 Pa
(+ 2666 Pa / -1600 Pa)
+ 4000 Pa / -2400 Pa
(+ 2666 Pa / -1600 Pa)
X
340 - 420 mm
+ 1200 Pa / -1200 Pa *
(+ 800 Pa / -800 Pa)
+ 3000 Pa / -3000 Pa
(+ 2000 Pa / -2000 Pa)
+ 4200 Pa / -4000 Pa
(+ 2800 Pa / -2666 Pa)
X
420 - 520 mm
+ 1200 Pa / -1200 Pa *
(+ 800 Pa / -800 Pa)
+ 2400 Pa / -2400 Pa
(+ 1600 Pa / -1600 Pa)
+ 3600 Pa / -2400 Pa
(+ 2400 Pa / -1600 Pa)
X
520 - 650 mm
+ 1800 Pa / -1800 Pa *
(+ 1200 Pa / -1200 Pa)
+ 2400 Pa / -2400 Pa
(+ 1600 Pa / -1600 Pa)
+ 2400 Pa / -2400 Pa
(+ 1600 Pa / -1600 Pa)
X
0 - 100 mm X
+ 1200 Pa / -1200 Pa *
(+ 800 Pa / -800 Pa)
+ 1600 Pa / -1600 Pa *
(+ 1066 Pa / -1066 Pa)
X
100 - 250 mm X
+ 800 Pa / -800 Pa *
(+ 533 Pa / -533 Pa)
+ 2400 Pa / -2400 Pa
(+ 1600 Pa / -1600 Pa)
X
Rail length under
module
100 - 200 mm
Min.
100
mm
Ma
x. 200 mm
0 - 208 mm X
+ 1200 Pa / -1200 Pa *
(+ 800 Pa / -800 Pa)
+ 1600 Pa / -1600 Pa *
(+ 1066 Pa / -1066 Pa)
X
208 - 340 mm
+ 1200 Pa / -1200 Pa *
(+ 800 Pa / -800 Pa)
+ 3600 Pa / -2400 Pa
(+ 2400 Pa / -1600 Pa)
+ 3600 Pa / -2400 Pa
(+ 2400 Pa / -1600 Pa)
X
340 - 420 mm
+ 1200 Pa / -1200 Pa *
(+ 800 Pa / -800 Pa)
+ 3000 Pa / -3000 Pa
(+ 2000 Pa / -2000 Pa)
+ 3000 Pa / -3000 Pa
(+ 2000 Pa / -2000 Pa)
X
420 - 520 mm
+ 1200 Pa / -1200 Pa *
(+ 800 Pa / -800 Pa)
+ 2400 Pa / -2400 Pa
(+ 1600 Pa / -1600 Pa)
+ 3600 Pa / -2400 Pa
(+ 2400 Pa / -1600 Pa)
X
520 - 650 mm
+ 1800 Pa / -1800 Pa *
(+ 1200 Pa / -1200 Pa)
+ 2400 Pa / -2400 Pa
(+ 1600 Pa / -1600 Pa)
+ 2400 Pa / -2400 Pa
(+ 1600 Pa / -1600 Pa)
X
0 - 100 mm X
+ 1200 Pa / -1200 Pa *
(+ 800 Pa / -800 Pa)
+ 1600 Pa / -1600 Pa *
(+ 1066 Pa / -1066 Pa)
X
100 - 250 mm X
+ 800 Pa / -800 Pa *
(+ 533 Pa / -533 Pa)
+ 2400 Pa / -2400 Pa
(+ 1600 Pa / -1600 Pa)
X
Once a module is secured in each of the 4 zones (fig. 2 ), additional clamps, i.e., ≥5 , may be freely located on panel frame without
a ff ecting the warranty. Loads marked with a
*
were not certified as part of IEC 61215 / 61730 testing; these have been evaluated by
REC’s internal testing process.