ReadyLift 69-21300 Скачать руководство пользователя страница 23

Страница: 23 / 25

www.ReadyLIFT.com

Phone: (877) 759

9991

21300

Install the rear track bar into the

track bar

bracket

using the supplied

M16 x 90mm

hex head bolt, washers and locking nut

Do not tighten at this time.

Using an appropriate jack, support the

axle.

Remove the

(3)

top strut nuts and the

lower strut bolt. Lowering the axle will aid

in the removal of the rear strut. Remove

the rear strut assembly from the vehicle.

Retain both the factory mounting hard-

ware and the strut.

With the rear strut assembly removed

from the vehicle, remove the locating pin

from the top hat using pilers or similar

tool.

Install the

top strut spacer

onto the rear

strut assembly using the factory nuts.

Torque the factory nuts to

30 ft

lbs

NOTE: INSTALL THE SPACER SO THE OFFSET IS

PERPENDICULAR TO THE LOWER MOUNTING

BOLT.

Содержание 69-21300


























Результаты поиска

Содержание 69-21300

Отзывы:

Похожие инструкции для 69-21300

Бренды по названию

Популярные бренды

ReadyLift 69-21300, Руководство пользователя

Результаты поиска

Содержание 69-21300

Отзывы:

Похожие инструкции для 69-21300

Бренды по названию

Популярные бренды