background image

 

8kHz:

 Is the PWM Frequency for a motor with 2 poles, usually an inrunner motor. 

However, the 16 kHz frequency can provide more power but will also cause more 
Electromagnetic Interference (EMI). Therefore, the default setting is 8kHz. 

 

16kHz:

 Is the PWM frequency for a motor with more than 2 poles, usually an 

outrunner motor.  

 

10.  Protection Mode for Low Voltage: Reduce Power / Hard Cutoff 

 

 

 

Reduce Power:

 The ESC will reduce the motors output power when the set 

“Low Voltage Protection” mode is reached to protect the battery from over discharging 
but still giving enough power to return the ESC. This parameter is recommended. 
 
 

Hard Cutoff

: The ESC will completely shut off the motors ouput power when the 

set “Low Voltage Protection” mode is reached to protect the battery from over 
discharging. 
 
 
 
 
 

 
Start-up Protection 

If the motor fails to startup normally in two seconds after push the throttle to start the ESC will 
cut off the motor. The throttle shall be reset to commence a restart. Possible reasons: there is a 
disconnection or poor contact in wiring between the ESC and motor. The propeller is stemmed 
by other objects. The speed reduction gear is badly blocked. 
 
 
Overheat Protection 
When the working temperature in the ESC is higher than 100

, the ESC will reduce the output 

power automatically to commence protection, but will reduce the output power to 40% of full 
power to reserve some power for motor and avoid crash landing instead of turning off all output 
power. The ESC will recover to max power as the temperature falls. 
 
 
Loss of Throttle Signal Protection 
The ESC will reduce the output power to motor when the ESC detect that there are 2 seconds' 
lost of throttle signals. If there another 2 seconds' lost of throttle signals, the ESC will cut off 
motor automatically. If the throttle signals recover during the Throttle Signal reduction of output 
power of motor, the ESC will recover control of throttle at once. In this method, in the case of 
momentary lost of signals (within 2 seconds), the ESC Loss Protection will not commence the 
protection of throttle. Only when the control signals have been lost for a long time, the ESC will 

07   ESC Protections 

Содержание 30A ES











Отзывы: