background image

22

Only use one wing at a time either the Primary or the Backup.

Make sure the wing you are not using is completely empty while diving so that 
you only have 1 air space to control.

The Primary wing can be inflated in the following ways:

•   

By using the power inflator connected to a tank with an LPI hose 

• 

 By oral inflation by holding down the dump button of the power inflator 
and blowing into the mouthpiece

The Primary wing can be vented in the following ways:

•   

By using the pull dump while rolling the body to the opposite side when in 
a horizontal position to get the dump valve to the highest position of the 
wing

•   

By using the dump valve on the power inflator when in a head up position

•   

By sucking a vacuum on the power inflator when in a head down position

The Backup wing can only be inflated orally using the bite on mouthpiece.

Not having a power inflator connected to the Backup wing avoids any prob-
lems associated with a mechanical failure or accidental inflation of the wing 
resulting in a potential buoyant ascent.

To use the oral inflation hose place the very end of the bite on mouthpiece 
between your teeth horizontally and make a seal around it with your lips. 

Step 6: Correct Use of the BAT Wing

2  Rigging the Razor BAT Wing

Содержание Bat Wing




























Отзывы: