Rayco RG25HD, Оператор, Сервис, Техническое обслуживание, Каталог запасных частей

Страница: 14 / 72

RG25DH Operation • Service • Maintenance • Parts Manual
14
Electrical Storm Injury Prevention
When lightning is striking in the vicinity of the machine, the
operator should never attempt to operate the machine. If you
are on the ground during an electrical storm, stay away from
the vicinity of the machine!
While Operating the Machine
All personnel using this Machine must be trained in the
operation, safety and maintenance repair procedures.
Careless use of this Equipment could result in serious injury
or even death.
ALL PROCEDURES IN THE SAFETY AND
OPERATION SECTIONS OF THIS MANUAL MUST
BE READ AND UNDERSTOOD BEFORE STARTING
THIS MACHINE.
• All operators must be wearing the proper Personal
Protective Equipment before attempting to start and
operate this machine.
• Do not allow children or other spectators to standby
and watch the machine in operation.
• Familiarize yourself with all of the controls in a safe
environment before starting to work with this machine.
• Always have more than one person at the job site. If an
accident occurs, someone is there to assist or obtain help.
• Never operate or allow someone to operate the machine
while under the influence of alcohol, drugs, or any
medication that could affect the operator’s performance
and concentration. Maintain a drug-free work place.
• Always operate this machine with all safety equipment in
place and working. Make sure all controls are properly
adjusted for safe operation.
• Do not change the engine governor settings or over
speed the engine. The governor controls the maximum
safe operating speed of the engine
• Never leave this machine unattended with the engine
running.
• Use only your hand to operate the controls. Never use
a foot, knee, rope or any extension device.
• Never hand-feed this machine for any reason.
• Contact with moving parts, belts or rotating cutter wheels
can kill, injure or dismember.
• Turn off engine and wait for all movement to stop before
working on this machine. Lock-out/Tag Out all controls.
• If equipped, the Emergency Stop buttons must be
operating properly. These should each be checked and
verified to shut down the engine by the operator prior
to performing any work.
• CAUTION! FLYING DEBRIS! NEVER stand or allow
anyone else to be directly in front of machine.
• Material being discharged from machine can cause
severe injury, blindness or death.
• Always operate this machine from the operator area.
Never stand directly in front of machine as flying objects
could be thrown during operation.
While Servicing and Performing
Maintenance on the Machine
• ALWAYS Block the wheels to prevent unintended
movement.
• Adhere to your LOCK-OUT/TAG-OUT procedure when
performing maintenance or repairs to this machine.
Locking and tagging out equipment safeguards
those working on equipment from being injured by its
unexpected energized or releasing stored energy.
• To prevent fires, clean debris and chaff from the engine
and muffler areas.
• Periodically check that all nuts and bolts, hose clamps,
and hydraulic fittings are tight.
• When removing the fuel cap, unscrew it slowly, and
hold it firmly. The cap may otherwise be thrown due to
pressure buildup caused by an increase in temperature.
• For your safety, repair or replace all damaged or worn
parts immediately. Replacement parts which are
authorized by Rayco are the only parts which should be
used for repair or replacement on this machine.
• Altering this equipment, or using this equipment in
such a way as to circumvent its design capabilities and
capacities, could result in serious injury or fatality and
WILL VOID THE WARRANTY.
• Do not alter this machine in any manner. Alterations
such as attaching a rope to the control bar may result
in personal injury or death.
• NEVER remove the cap from the hydraulic tank or
reservoir while the machine is running. Hot oil under
pressure will cause injury.
• Relieve hydraulic system pressure before repairing
or adjusting fittings, hoses, tubing, or other system
components.
Before Starting Engine
Start the engine only from the operator compartment. Never
short across the starter terminal or across the batteries.
Shorting could damage the electrical system by bypassing
the engine neutral start system.
Before you start the engine and before you move the machine,
make sure that no one is underneath the machine, around
the machine, or on the machine. Make sure that the area is
free of personnel.
Visibility Information
Before you start the machine, perform a walk-around
inspection in order to ensure that there are no hazards
around the machine.
Safety