Rayco RG25HD Скачать руководство пользователя страница 43

Страница: 43 / 72

RG25DH Operation • Service • Maintenance • Parts Manual

800.392.2686

Maintenance

6. Check the brake/clutch pedal to make sure that when the pedal is depressed that the idler pulley is releasing

the belt tension before it applies the brake. If this does not happen the unit will still be under a load and be

impossible to shift.

7. The ﬁnal area to check would be for damaged or binding shift linkage.

Hard shifting with the engine off could be caused by:

1. Shift linkage out of adjustment.

2. Corrosion in the transaxle or transmission.

3. Damaged shift keys, gears, or shifter brake shaft.

4. Belt guides missing or improperly adjusted (see equipment manufacturer specs).

Unit seems to slip:

1. Check for proper belt adjustment (consult O.E.M. operator's manual).

2. Check for proper clutch/brake adjustment (consult O.E.M. operator's manual).

3. Check pulley condition and wheels for sheared or damaged keys.

4. Check drive belt condition, if glazed or worn, replace it.

5. Possible internal transmission damage. We suggest you contact a local

Rayco Dealer

Basic Gear Drive Troubleshooting -

continued

NOTE

Before troubleshooting any system problem, see original equipment manufacturer’s (O.E.M.) instructions.

Make your troubleshooting easier by preparing as follows:

•

Work in a clean, well-lighted place.

•

Keep proper tools and materials nearby.

•

Keep an adequate supply of clean petroleum-based solvent.

To avoid carbon monoxide poisoning, make sure engine is outdoors in a well-ventilated area.

Some maintenance procedures cannot be performed until the vehicle wheels are secured and off

the ground. Failure to do so could result in death or serious injury to yourself and/or bystanders.

DO NOT

attempt any maintenance procedures with the engine running. Doing so could result in

death or serious injury to yourself and/or bystanders.

Use care when performing inspection of the drive belt assembly including all vehicle linkage.

Failure to do so could result in death or serious injury to yourself and/or bystanders.

Troubleshooting Chart

Use of this troubleshooting chart will aid in determining the source of a problem; the hydrostatic transmission,

ﬁnal drive or vehicle's belt drive and/or linkage systems.

TecumsehPower Hydrostatic Transaxle

Troubleshooting

Final Drive

Hydrostatic

Transmission

TecumsehPower and Peerless Transmission, Transaxle and Gear

SYMPTOM

PROBLEM

CORRECTIVE ACTION

REDUCED POWER

Improper belt tension

Belt worn, replace

Belt worn, glazed, or oil saturated

Replace belt

Drive pulley worn

Replace pulley and belt

(See O.E.M. equipment manual)

Brake set too tight

Set brake adjustment

(See O.E.M. equipment manual)

Shifter linkage misadjusted or broken

Linkage damaged or loose, replace or adjust

(See O.E.M. equipment manual)

Fluid low in hydrostatic transmission

Check and add ﬂuid if low (Part No. 730228A)

Hydrostatic transmission bad

Replace hydrostatic transmission

DIFFICUL

TO SHIFT

Linkage broken or bent

Repair or replace linkage

(See O.E.M. equipment manual)

Hydrostatic transmission pump seized

Replace hydrostatic transmission

Hydrostatic transmission control friction

pack misadjusted

Replace friction pack washers, tighten nut

to 100 in. lbs. (11.2 Nm) loosen nut 4-turns

WARNING

SYMPTOM

PROBLEM

CORRECTIVE ACTION

UNIT IS NOISY

Final drive gear noise

Check, add gear oil to ﬁnal drive

Check, replace worn gears

Check, replace worn bearings

Hydrostatic transmission noise

Replace hydrostatic transmission

Transaxle clicking

Mechanical disconnect not properly engaged,

check for obstruction

Check, replace mechanical disconnect

components (If hydrostatic transmission

shaft is damaged, replace transmission)

DOES NOT DRIVE

Improper belt tension

Belt worn, replace

(See O.E.M. equipment manual)

Brake setting incorrect

Adjust brake to proper setting

(See O.E.M. equipment manual)

Belt worn, glazed, or oil saturated

Replace belt

(See O.E.M. equipment manual)

Drive pulley worn

Replace pulley and belt

(See O.E.M. equipment manual)

Transaxle - hydrostatic transmission bad

Replace hydrostatic transmission

Shifter linkage misadjusted or broken

Linkage damaged or loose, replace or adjust

(See O.E.M. equipment manual)

Fluid low in hydrostatic transmission

Check and add ﬂuid if low (Part No. 730228A)

Disconnect is in freewheel position

Move control to connected position

(See O.E.M. equipment manual)

Sheared or missing axle key

Replace missing or broken key

Damaged or broken ﬁnal drive gear

Check, replace worn or damaged gear

Hydrostatic transmission leaking

Replace hydrostatic transmission

LEAKING LUBRICANT

Hydrostatic transmission leaking

Replace hydrostatic transmission

Final drive leaking at seam

Split ﬁnal drive housing, clean old sealant off,

replace seals, apply new sealant (torque bolts

80-120 in. lbs.[9.0 Nm - 13.5 Nm])

Final drive leaking at shaft seal

Split ﬁnal drive housing, clean old sealant off,

replace seals, apply new sealant (torque bolts

80-120 in. lbs. [9.0 Nm - 13.5 Nm])

BRAKE NOT WORKING

Linkage out of adjustment

Adjust brake linkage

(See O.E.M. equipment manual)

Linkage bent or broken

Replace components, set brake

(See O.E.M. equipment manual)

Brake setting incorrect

Adjust brake to proper setting

(See O.E.M. equipment manual)

TecumsehPower Transaxle Troubleshooting -

continued

Содержание RG25HD








































































Результаты поиска

Содержание RG25HD

Отзывы:

Похожие инструкции для RG25HD

Бренды по названию

Популярные бренды

Rayco RG25HD, Оператор, Сервис, Техническое обслуживание, Каталог запасных частей

Результаты поиска

Содержание RG25HD

Отзывы:

Похожие инструкции для RG25HD

Бренды по названию

Популярные бренды