Rayco RG25HD Скачать руководство пользователя страница 47

Страница: 47 / 72

RG25DH Operation • Service • Maintenance • Parts Manual

800.392.2686

Troubleshooting

Light Duty Hydrostatic

Model 6

The Model 6 transmission is designed

primarily for light duty applications requiring

up to 1,9 Kw [2.5 hp] output for continuous

operation.

Operation

For optimum control and power, the

transmissions should be operated at

constant input speeds. When operating the

unit under varying load conditions there can

be noticeable changes in the output speed. If

the output speed decreases due to increased

load, the shift lever should be directed

toward neutral position to increase the

output torque. This produces the same

result as shifting down to a lower gear with a

typical mechanical transmission.

The Model 6 transmission can include a dump

valve which, when actuated, enables the

vehicle to be pushed with the engine off.

Caution: Motor speed must not exceed 350

RPM when the valve is actuated.

Drive

A belt drive is preferred, with the sheave

diameter 102 mm [4 in.] or less. Be sure to

locate the belt over the input shaft bearing

because excessive side loading can cause

problems. Follow the belt manufacturer’s

recommendation for belt tension to transmit a

maximum of 3 Kw [4 hp]. The unit can be

driven direct with a flexible coupling between

an engine or motor and the input shaft of the

transmission. Be sure the two shafts are in

alignment.

Cooling

Proper cooling is essential to both performance

and life of the transmission. The recommended

maximum oil operating temperature is 82

[180

F]. In order to provide adequate cooling,

an 200 mm [8 in.] diameter fan should be used

on the input side. If properly designed and

installed, the fan will effectively cool the

transmission up to approximately four input

horsepower.

Fluid

See Bulletin 3-401 for recommended fluids. The

standard factory fill is premium hydraulic fluid

having a viscosity equivalent to SAE 20W20.

Options

• Wide Band Neutral

• Dump Valve

Model 6

Internal Reservoir/Expansion Tank

Air Bleed Plug

Output Shaft

Dump Valve

Tapered

Control Shaft —

for Installation

of a Customer

Control Lever

Recommended Center Line of Drive Sheave

Coupling and

Pulley

(Customer

Supplied)

Input Shaft

Cooling

Fan

(Customer

Supplied)

Control Lever Length — 100 mm [4 inch]

End of

Shaft

35 mm [1.4 in.]

Содержание RG25HD








































































Результаты поиска

Содержание RG25HD

Отзывы:

Похожие инструкции для RG25HD

Бренды по названию

Популярные бренды

Rayco RG25HD, Оператор, Сервис, Техническое обслуживание, Каталог запасных частей

Результаты поиска

Содержание RG25HD

Отзывы:

Похожие инструкции для RG25HD

Бренды по названию

Популярные бренды