Rayburn Heatranger 368K Скачать руководство пользователя

Страница: 24 / 25

SYMPTOMS

CAUSE

REMEDY

COOKER BURNER

FAULT FINDING

BURNER WILL NOT LIGHT.

Check wicks in position.

Fit wicks.

Lack of oil to burner.

Check oil valve switched on.
Check oil valve trip is down.
Check oil feed pipe gradient
ensure steady rise.

NO HIGH FIRE.

Control valve setting wrong.

Check control valve knob is set
at maximum.

Sticking control valve pin.

Replace control valve top.

SOOTY FLAME-LOW FIRE.

Poor fitting burner shells.

Check set of shells seating properly
Replace set of shells.
Check burner base, replace
if necessary.

Low fire oil rate incorrect.

Reset oil rate.

SOOTY FLAME-HIGH FIRE.

Oil rate to high.

Re-adjust high fire oil rate.

Down Draughts.

Check flue for down draughts and
eliminate them.

Poor fitting burner shells.

Check set of shells seating properly
Replace set of shells.
Check burner base, replace if
necessary.

CONTINUOUS LOW FIRE.

Power failure.

Check mains supply: if power cut
use manual control.

Cooker thermostat fault.

Replace cooker thermostat.

Oil valve electric top fault.

Replace electric top.

Oil valve control pin stuck.

Free using manual control lever.

CONTINUOUS HIGH FIRE.

On manual over ride.

Return manual over ride lever to
low position.

Cooker thermostat fault.

Replace cooker thermostat.

Oil valve electric top fault.

Replace electric top.

ABNORMALLY LOW OVER

Oil starvation.

Check oil supply.

NIGHT TEMPERATURE

Air lock in oil feed pipe.

Check oil feed pipe rises over
whole length.

Air lock in burner feed pipe.

Check burner feed pipe gradient
and cleanliness.

Содержание Heatranger 368K


























Результаты поиска

Содержание Heatranger 368K

Отзывы:

Похожие инструкции для Heatranger 368K

Бренды по названию

Популярные бренды

Rayburn Heatranger 368K, Инструкции по установке и обслуживанию

Результаты поиска

Содержание Heatranger 368K

Отзывы:

Похожие инструкции для Heatranger 368K

Бренды по названию

Популярные бренды