Rasilient PixelStor 5000 Скачать руководство пользователя страница 132

Страница: 132 / 161

Hardware Installation

PixelStor 5000 User Manual
Rev. 1, May 2013

7-95

dasysalert

used to enable or disable health alerts

daum

used to upgrade or manage kernel images

davd

used to manage virtual disks

daversion

used to display version information of kernel

images or boot images

Figure 7-1 CLI command list

7.7

The CLI Commands

The CLI Commands for the

PixelStor 5000

have the prefix

“da” as part of the command

name. The commands and their descriptions are listed below.

7.7.1

daacl

Use daacl to manage the access control list on at a system level.

daacl - manage access control list.

Usage:

daacl [Options]

Options:

-h/--help: help

-L/--list: list all allowed addresses

-a [address/prefixlen]: add an address into the allowed list

-d [address/prefixlen]: delete an address from the allowed list

Command Examples:

daacl -a 0.0.0.0/0: allow access from all

daacl -a 192.168.1.0/24: allow access from one subnet

daacl -a 192.168.1.1/32: allow access from one IP

7.7.2

daaddrbk

Use daaddrbk to manage the email addresses for notification.

daaddrbk - add email address to notification list.

Содержание PixelStor 5000


































































































































































Результаты поиска

Содержание PixelStor 5000

Отзывы:

Похожие инструкции для PixelStor 5000

Бренды по названию

Популярные бренды

Rasilient PixelStor 5000, Руководство пользователя

Результаты поиска

Содержание PixelStor 5000

Отзывы:

Похожие инструкции для PixelStor 5000

Бренды по названию

Популярные бренды