Rasilient PixelStor 5000 Скачать руководство пользователя страница 54

Страница: 54 / 161

Hardware Installation

PixelStor 5000 User Manual
Rev. 1, May 2013

4-17

1. Power-on PixelStor 5000, using the DC power/standby switch-on each power supply.

The green DC power light on the power supply will turn on and stay on. The green

activity light on each installed disk drive should be on. The PixelStor 5000 comes with its

own pre-installed system software. When the system is powered on, the system

software boots automatically.

2. Move to a workstation with a web browser such as Microsoft Internet Explorer on the

same subnet as PixelStor 5000 . Type http://192.168.0.1 into the web browser address

window to access the PixelStor Storage Manager.

3. You will see the PixelStor 5000 login. Enter the following login information when

prompted.



Password: root



User Name: root

4. This will take you to Systems Properties page. Use the Setup Wizard on the far right

side of the browser window (Steps 1-6) to guide you through the setup process.

4.1.2

Option 2 – Configure Private IP Address to Connect to System

Before connecting the PixelStor 5000 to your network, you will first need to access the built-in

Command Line Interface (CLI) that is included with your system. The PixelStor 5000 is

designed with one mini-serial port on the back of each controller module. This can be used to

There will be only one base System IP address regardless of number of physical

GE ports or number of controllers.

When PixelStor 5000 is started for the first time, the system may take 1-2 minutes

as it does a full system check. This only happens on the first start-up or after an

improper power shut down. If the system is restarted during the initialization

sequence, the process starts over from the beginning. Please wait for the system to

finish its initialization sequence to avoid start-up delays.

The workstation that will be used for system configuration should be on the same

subnet as PixelStor 5000 . Set the Workstation IP address to 192.168.0.x and the

net mask to 255.255.255.0 before trying to access the PixelStor Storage

Manager.

Содержание PixelStor 5000


































































































































































Результаты поиска

Содержание PixelStor 5000

Отзывы:

Похожие инструкции для PixelStor 5000

Бренды по названию

Популярные бренды

Rasilient PixelStor 5000, Руководство пользователя

Результаты поиска

Содержание PixelStor 5000

Отзывы:

Похожие инструкции для PixelStor 5000

Бренды по названию

Популярные бренды