Rasilient PixelStor 5000 Скачать руководство пользователя страница 127

Страница: 127 / 161

Hardware Installation

PixelStor 5000 User Manual
Rev. 1, May 2013

6-90

performance and the best fault-tolerance in a multi-user system. 100% redundancy of

data means no rebuild is necessary in case of a disk failure, just a copy to the

replacement disk. Also, under certain circumstances, RAID 1 can sustain multiple

simultaneous drive failures.



Cons - highest disk overhead of all RAID types (100%).



Ideal applications - those that require very high availability.

RAID 5 -

Distributed Parity - RAID-5 stores parity information but not redundant data.

The parity information can be used to reconstruct data. RAID-5 requires at least three

disks for the array.



Pros - This is the best combination of performance and cost.



Cons

– Disk failure has some impact on throughput.



Ideal Applications - this is the most versatile RAID level and is applicable to a broad

range of applications. It is best for multi-user systems in which performance is not

critical or applications that require few write operations.

RAID 6

–

Block-level striping with

dual

distributed parity

– Like RAID 5, RAID 6 stripes

data and parity across an array of drives with the additional capability to calculate two

sets of data parity for each volume of data. Requires at least 4 disks for the array.



Pros - Extremely high data fault tolerance. Provides protection against double disk

failures and failures while a single disk is rebuilding while other RAID levels can handle

at most one fault.



Cons

– RAID 6 performance can be slightly worse than RAID 5 in terms of writes due to

the added overhead of more parity calculations. RAID 6 is inefficient when used with a

small number of drives due to need for 2 parity drives.



Ideal Applications

– Complex, higher capacity SATA arrays (12-24 drives) where higher

availability is critical.

RAID 10 -

Combination of mirroring and striping - This type offers an array of stripes in

which each stripe is a RAID-1 array of drives.



Pros -This offers higher performance than RAID-1



Cons- but at much higher cost.



Ideal Applications- those requiring high performance and fault tolerance.

Содержание PixelStor 5000


































































































































































Результаты поиска

Содержание PixelStor 5000

Отзывы:

Похожие инструкции для PixelStor 5000

Бренды по названию

Популярные бренды

Rasilient PixelStor 5000, Руководство пользователя

Результаты поиска

Содержание PixelStor 5000

Отзывы:

Похожие инструкции для PixelStor 5000

Бренды по названию

Популярные бренды