Rasilient PixelStor 5000 Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 161

background image

Hardware Installation

PixelStor 5000 User Manual
Rev. 1, May 2013

3-2

To shut down power supply:

Press the power switch \ to the off position. This will turn off the green AC power LED

, AC

power fault

and chassis power DC on

.

Figure 3-1 Shut Down Power Supply

To unplug the power cords:

First unplug the power cords from the AC outlet and then from the storage.

3.2

Installing in a Rack

The rail kit included with the system can be used to mount the PixelStor 5000 in 4-post racks

with square holes or with round holes.

3.2.1

Rack preparation

Review the rack manufacturer’s documentation to become familiar with their installation
requirements. Locate the chassis brackets that are supplied with the PixelStor 5000. Have them

ready for use in the rack installation. If you are installing more than one PixelStor 5000 into the

rack, start at the lowest available position, and work upward. You may need to remove the
rack’s power distribution unit (PDU) before you install the PixelStor 5000. Refer to rack
manufacturer’s instructions for further instructions



A stabilizer must be attached to the bottom, front of the rack to prevent the

rack from tipping forward while the enclosure is being removed or installed. Do

not remove or install any enclosure if a stabilizer is not attached to the rack.



Do not attempt to lift the enclosure by yourself. Ask another person for aid.



Do not use the handles from the controller or power supply modules to carry

the enclosure. These handles are not intended to support the weight of the

enclosure.

«
...
37
38
39
40
41
...
»

Содержание PixelStor 5000


































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PixelStor 5000

Бренд: Cactus Страницы: 27

Бренд: Naterial Страницы: 21

Бренд: Quantum Страницы: 384

Бренд: Tandberg Data Страницы: 60

Бренд: Dancover Страницы: 30

Бренд: U-Line Страницы: 5

Бренд: Patiowell Страницы: 27

Tape Library Magstar 3494

Бренд: IBM Страницы: 378

B. spaces Tidy Toybox

Бренд: Maison Battat Страницы: 2

Бренд: Raidon Страницы: 2

Бренд: SanDisk Страницы: 2

Бренд: NEC Страницы: 4

Бренд: NEC Страницы: 8

Бренд: NEC Страницы: 12

Бренд: NEC Страницы: 48

Бренд: NEC Страницы: 53

Бренд: NEC Страницы: 106

Бренд: NEC Страницы: 118

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды