background image

6

RAMSET

www.ramsetinc.com

RAM 100 • 1000 • 5500

MODEL RAM 100

RAM 1000

RAM 5500 3/4 HP

RAM 5500 1HP

MAX. GATE TRAVEL

20 feet

45 feet

45 feet

45 feet

MAX. GATE WEIGHT

700 lbs

1000 lbs

1500 lbs

2500 lbs

CYCLES

Continuous

Continuous

Continuous

Continuous

CAPACITOR

Aerovox 65µƒ, 240 V, 50/60 
HZ, protected S 1000AFC

Aerovox 65µƒ, 240 V, 50/60 
HZ, protected S 1000AFC

Aerovox 50µƒ & 65µƒ, 240 
V, 50/60 HZ, protected S 
1000AFC

Aerovox 75µƒ & 75µƒ, 240 
V, 50/60 HZ, protected S 
1000AFC

APPLICATION

Residential/ Commercial

Commercial/ Industrial

Commercial/ Industrial

Commercial/ Industrial

FINISH AND 

CONSTRUCTION

Gold/Zinc plated
3/16” H.R. Metal

Gold/Zinc plated
3/16” H.R. Metal

Gold/Zinc plated
3/16” H.R. Metal

Gold/Zinc plated
3/16” H.R. Metal

CONTINUOUS DUTY 

MOTOR

1/2 Hp 115 Volts. AC
4.5 amp. 1625 rpm.

1/2 Hp 115 Volts. AC
4.5 amp. 1625 rpm.

3/4 Hp 115 Volts. AC
8.5 amp. 1625 rpm.

1 Hp 115 Volts. AC
9.4 amp. 1625 rpm.

POWER FAILURE

RELEASE

Exclusive Foot Pedal 
Release (RPI-TL only)

Exclusive foot pedal release 
or optional battery back-up 
system (BBS or RPI-TL)

Exclusive foot pedal release 
or optional battery back-up 
system (*BBS or RPI-TL)

Exclusive foot pedal release 
or optional battery back-up 
system (*BBS or RPI-TL)

OVERALL DIMENSIONS

H 22” - L 14½” - W 15”

H 27” - L 16” - W 16½”

H 27” - L 16” - W 16½”

H 27” - L 16” - W 16½”

GATE TRAVEL SPEED

Approx. 1’ per sec

Approx. 1’ per sec

Approx. 1’ per sec

Approx. 1’ per sec

SHIPPING WEIGHT

110 lbs

125 lbs

135 lbs

135 lbs

FOOT

PEDAL

RELEASE

EMERGENCY RELEASE

Exclusive foot pedal release disengages the gate 

from the motor so it can be opened manually.

GENERAL SPECIFICATIONS

Note:

Model RAM 1000 and RAM 5500 can be 

used for center and rear installation with 

gates up to 25’ maximum.

WARNING

Do not exceed the specifications. The warranty on your unit will be void if the 

installation exceeds the recommended specifications.

RAM 100

RAM 1000

RAM 5500

Note:

Model RAM 100

is designed to be

installed only for

front installations.

*BBS is only capable for 1000 lb gates or less.

3/4 Hp

(1Hp not shown)

Содержание RAM 100
































Отзывы: