RAMSET RAM 100 Скачать руководство пользователя страница 28

Страница: 28 / 31

RAMSET

www.ramsetinc.com

RAM 100 • 1000 • 5500

GATE ENTRANCE SAFETY PRECAUTIONS

1. READ AND FOLLOW ALL INSTRUCTIONS
2. Never let children operate or play with gate controls. Keep the

remote control away from children.

3. Always keep people and objects away from the gate. NO ONE

SHOULD CROSS THE PATH OF THE MOVING GATE.

4. Test the gate operator monthly. The gate MUST reverse on

contact with a rigid object or stop when an object activates the

non-contact sensors. After adjusting the force or the limit of travel,

retest the gate operator. Failure to adjust and retest the gate

operator properly can increase the risk of injury or death.

5. Use the emergency release only when the gate is not moving.
6. KEEP GATES PROPERLY MAINTAINED. Read the user’s

manual. Have a qualified service person make repairs to gate

hardware.

7. The entrance is for vehicles only. Pedestrians must use separate

entrance.

8. SAVE THESE INSTRUCTIONS.

IMPORTANT SAFETY INSTRUCTIONS

WARNING

To reduce the risk of severe injury or death:

Содержание RAM 100
































Результаты поиска

Содержание RAM 100

Отзывы:

Похожие инструкции для RAM 100

Бренды по названию

Популярные бренды

RAMSET RAM 100, Инструкция по эксплуатации

Результаты поиска

Содержание RAM 100

Отзывы:

Похожие инструкции для RAM 100

Бренды по названию

Популярные бренды