background image

3

RAM 100 • 1000 • 5500

RAMSET

www.ramsetinc.com

RESPONSIBILITIES OF INSTALLERS AND TECHNICIANS cont.

•  WARNING SIGNS MUST BE PERMANENTLY AFFIXED TO THE GATE PANEL IN A HIGHLY VISIBLE 

PLACE THAT CAN BE EASILY SEEN FROM BOTH SIDES OF THE GATE.

•  A SEPARATE ENTRANCE IS SUPPLIED FOR PEDESTRIANS. THE OPERATOR IS INTENDED FOR 

INSTALLATION ONLY FOR GATES USED FOR VEHICLES.

•  THE GATE MUST BE INSTALLED IN A LOCATION SO THAT ENOUGH CLEARANCE IS SUPPLIED 

BETWEEN THE GATE AND ADJACENT STRUCTURES WHEN OPENING AND CLOSING TO 

REDUCE THE RISK OF ENTRAPMENT.

•  ALL CONTROLS MUST BE LOCATED AT LEAST 6 FEET AWAY FROM ANY PART OF THE GATE 

OPERATOR OR MOVING GATE AT ALL TIMES.

•  INTERIOR CONTROL STATIONS SHOULD BE INSTALLED SO THAT THE USER HAS A DIRECT 

LINE OF SIGHT TO THE GATE AREA BEING CONTROLLED.

•  PHOTOCELLS SHOULD BE INSTALLED WITHIN 5 INCHES FROM THE GATE PANEL AND A 

MAXIMUM HEIGHT OF 27.5 INCHES.

•  A PHOTOCELL IS A SAFETY DEVICE FOR PEDESTRIANS ONLY; VEHICLE DETECTORS SHOULD 

ALWAYS BE USED FOR DETECTION OF MOTOR VEHICLES.

•  NO SAFETY DEVICES SHOULD EVER BE BYPASSED, REMOVED OR OMITTED BY THE 

INSTALLER/TECHNICIAN. A SIGNED WAIVER DOES NOT NULIFY THE INSTALLER/TECHNICIANS 

LIABILITY DUE TO THE FACT THAT IT HAS NO SUBSTANCE IN LITIGATION INVOLVING AN 

INJURED PARTY WHO DID NOT SIGN THE WAIVER.

•  IF YOU ARE INSTALLING THE OPERATOR ON A GATE THAT DID NOT HAVE AN OPERATOR ON 

IT, THE GATE MUST CONFORM TO THE CURRENT ASTM F 2200 STANDARDS.

•  IF YOU ARE INSTALLING THE OPERATOR ON A GATE THAT ALREADY HAD AN OPERATOR ON 

IT, THE TECHNICIAN/INSTALLER SHOULD ADVISE THE CUSTOMER OF THE UPGRADES THAT 

ARE NEEDED TO BRING THE GATE UP TO THE CURRENT ASTM F 2200 STANDARDS.

•  WHEN INSTALLING OR WORKING ON A GATE OPERATOR SYSTEM, ALWAYS MAKE SURE 

THAT THE AREA AROUND YOU IS SECURE. USE CONES, YELLOW CAUTION TAPE OR WHEN 

POSSIBLE, BLOCK OFF THE DRIVEWAY FROM TRAFFIC.

•  WHEN NECESSARY, INSTALL SURGE/LIGHTNING SUPPRESSION AND GROUND RODS.

•  ALL AREAS THAT ARE AT RISK OF ENTRAPMENT SHOULD BE PROTECTED BY AN ANTI-

ENTRAPMENT DEVICE.

•  MAKE SURE TO INSTALL POSITIVE STOPS ON THE FULL OPEN & IF NECESSARY, ON THE FULL 

CLOSED.

•  ALWAYS REMEMBER, YOU ARE THE TRAINED PROFESSIONAL AND WHAT A CUSTOMER 

WANTS SHOULD NEVER SUPERCEDE SAFETY.

Содержание RAM 100
































Отзывы: