RAMMER RSS05R Скачать руководство пользователя страница 68

Страница: 68 / 92

Page 68 - Maintenance

Troubleshooting

RSS05R, RSS08R, RSS11R, RSS15R, RSS23R, RSS34R,

RSS45R, RSS58R, RSS80R

8. TROUBLESHOOTING

8.1 PRODUCT DOES NOT CRUSH

WORN JAW

Perform new hardfacing. See “Hardfacing the jaw” on page 57.

DROP IN HYDRAULIC PRESSURE ON BASE MACHINE

Adjust pressure. See “Product specifications” on page 72.

OIL LEAKAGE WITHIN CYLINDER

The product must be serviced in an authorized Rammer service shop.

8.2 PRODUCT DOES NOT CUT

WORN CUTTING BLADES

Turn over the cutting blades and adjust. If necessary, change the cutting blades. See
“Turning and changing cutting blades” on page 53.

CUTTING BLADE DOES NOT FIT PROPERLY ONTO THE CUTTER BASE

Refit and tighten with bolts. See “Turning and changing cutting blades” on page 53.

INCORRECT CLEARANCE BETWEEN THE BLADES AND BASE

Check the clearance and adjust. See “Turning and changing cutting blades” on page
53.

DROP IN HYDRAULIC PRESSURE ON BASE MACHINE

Adjust pressure. See “Product specifications” on page 72.

OIL LEAKAGE WITHIN CYLINDER

The product must be serviced in an authorized Rammer service shop.

8.3 JAW DOES NOT MOVE

MALFUNCTION IN CARRIER HYDRAULIC SYSTEM

Check the operation of the auxiliary circuit.

BALL VALVES MAY BE CLOSED

Open the ball valves.

JAW MAY BE BLOCKED

Remove obstacles.

OIL LEAKAGE WITHIN CYLINDER

The product must be serviced in an authorized Rammer service shop.

Содержание RSS05R























































































Результаты поиска

Содержание RSS05R

Отзывы:

Похожие инструкции для RSS05R

Бренды по названию

Популярные бренды

RAMMER RSS05R, Руководство оператора

Результаты поиска

Содержание RSS05R

Отзывы:

Похожие инструкции для RSS05R

Бренды по названию

Популярные бренды