RAMMER RSS05R Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 92

background image

Operation - Page 11

COPYRIGHT © 2019 SANDVIK MINING AND CONSTRUCTION OY

Product introduction

RSS05R, RSS08R, RSS11R, RSS15R, RSS23R, RSS34R,
RSS45R, RSS58R, RSS80R

Place a chain or sling as shown in the illustration to lift the product.

Note: The lifting eye screws must always be removed from the product and replaced
with a screw before operation.

SAFETY INSTRUCTIONS FOR LIFTING

Below are some common safety instructions concerning lifting operations. In
addition to this, the local, national standards for machines and lifting-tackles must
always be strictly observed. Please note that the list below is not all inclusive, you
must always ensure the procedure you choose is safe for you and others.

■

Do not lift the load over people. No one must be under the hoisted load.

■

Do not lift people and never ride the hoisted load.

■

Keep people clear from the lift area.

■

Avoid side pull of the load. Make sure you take up the slack slowly. Start and
stop carefully.

■

Lift the load a few centimeters and verify it before proceeding. Make sure the
load is well balanced. Check for any loose items.

■

Never leave the suspended load unattended. Maintain load control at all times.

■

Never lift the load over the rated capacity (see the product's operating weight
from the specification page).

■

Inspect all lifting product before use. Do not use twisted or damaged lifting
product. Protect lifting product from sharp corners.

■

Obey all local safety instructions.

MB010013

«
...
9
10
11
12
13
...
»

Содержание RSS05R





























































































Отзывы:

Нет отзывов

Похожие инструкции для RSS05R

Бренд: Jarvis Страницы: 12

Бренд: hager Страницы: 4

Бренд: hager Страницы: 2

Бренд: OETIKER Страницы: 30

Бренд: Pulsar Страницы: 8

Бренд: Porter-Cable Страницы: 32

Бренд: Hakko Electronics Страницы: 2

Бренд: Dahua Technology Страницы: 28

Бренд: Parkside Страницы: 80

Бренд: MasterCraft Страницы: 30

Бренд: Broadata Страницы: 22

Бренд: Caillau Страницы: 14

Бренд: unicraft Страницы: 16

Бренд: Milwaukee Страницы: 32

Бренд: TDK-Lambda Страницы: 20

Бренд: Narex Страницы: 32

Digital Knight DK16

Бренд: Geo Knight Страницы: 25

Бренд: Matatakitoyo Torque Tools Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды