RAMMER RSS05R Скачать руководство пользователя страница 50 | Manualshive

Страница: 50 / 92

background image

COPYRIGHT © 2019 SANDVIK MINING AND CONSTRUCTION OY

Page 50 - Maintenance

Routine maintenance

RSS05R, RSS08R, RSS11R, RSS15R, RSS23R, RSS34R,

RSS45R, RSS58R, RSS80R

1. ROUTINE MAINTENANCE

1.1 OVERVIEW

This product is a precision-made hydraulic machine. Therefore, great care and
cleanliness should be taken when handling any of the hydraulic components. Dirt is
the worst enemy in hydraulic systems.

Handle the parts carefully and remember to cover any cleaned and dried parts with
a clean, lint-free cloth. Do not use anything other than purpose-designed materials
for cleaning hydraulic parts. Never use water, paint thinners or carbon tetrachloride.

Components, gaskets and seals in the hydraulic system should be oiled with clean
hydraulic oil before assembly.

Remember to grease the product parts regularly, according to the instructions in this
manual.

Prior to maintenance or inspection, operate all the control levers to their fully
extended stroke. This will release pressure within the hydraulic piping and prevent
unexpected movement of the jaw and loss of oil through the hydraulic lines.

Close the jaws during maintenance or inspection. If you must leave the jaws
open, remember to block the jaws to prevent them from closing.

1.2 INSPECTION AND MAINTENANCE BY THE OPERATOR

Note: The times given refer to the carrier hours with the product installed.

EVERY EIGHT HOURS

Grease shafts and pins.

DAILY MAINTENANCE

1. Check the hydraulic hoses and hose connections. Tighten if necessary.

2. Check the cutting blades and their clearance. Tighten bolts or replace the

cutting blades, if necessary. See “Turning and changing cutting blades” on page
53.

3. Check the jaws and teeth for wear. Hardface or replace, if necessary. See

“Hardfacing the jaw” on page 57.

4. Check the grease nipples.

«
...
48
49
50
51
52
...
»

Содержание RSS05R





























































































Отзывы:

Нет отзывов

Похожие инструкции для RSS05R

Бренд: Omega Страницы: 8

Бренд: Park Tool Страницы: 6

Бренд: Gallagher Страницы: 90

Бренд: Gallagher Страницы: 24

Бренд: E-Lite Страницы: 4

Бренд: Jet Страницы: 20

Бренд: Jet Страницы: 28

Бренд: Gage Bilt Страницы: 24

NEWMAR Sentinel

Бренд: Mission Critical Страницы: 28

Бренд: Chicago Pneumatic Страницы: 33

Бренд: Ryobi Страницы: 13

Бренд: K-Tool Страницы: 20

Бренд: Parkside Страницы: 28

Бренд: Banner Страницы: 2

Бренд: YATO Страницы: 88

Бренд: Fein Страницы: 31

Бренд: Gern Pro Страницы: 25

Autronic ACR Series

Бренд: Forte Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды