Radstone PMCGA1-101 Скачать руководство пользователя

Страница: 101 / 113

PPC7A Product Manual

Specifications

A-3

Edition

Local Resources

Processor

PowerPC 745x at 500 MHz or above.

SDRAM

64 to 512 Mbytes with ECC.

L2 or L3 Cache

1 to 4 Mbyte on private cache bus.

Graphics

Totally integrated 2D graphics processor with 2Mbytes of
graphics SRAM on chip.

With 69000:

Pixel clocks up to 135Mhz, up to 24 bit colour depths per pixel.

1280 x 1024 x 8 @ 75Hz
1024 x 768 x 16 @ 85 Hz
800 x 600 x 24 @ 85 Hz

With 69000:

Pixel clocks up to 170Mhz, up to 24 bit colour depths per pixel.

1280 x 1024 x 24 @ 80Hz
1024 x 768 x 24 @ 85 Hz
800 x 600 x 24 @ 85 Hz

FLASH

Up to 256 Mbytes, with 8 Mbytes reserved for Boot FLASH
banks

RTC

I²C RTC backed up by connection to VMEbus 5VSTDBY pin.

NVRAM

32 Kbytes.

PCI

64-bit @ 66 MHz.

SCSI

8 bit fast Ultra-SCSI via the P2 connector.

Ethernet

2 off, Ethernet 10/100BaseT via the P2 connector.

PMC Slots

Air-cooled: Two 5V, 32-bit IEEE P1386.1 compliant slots with
front panel and P0 I/O, and restricted P2 I/O.

Serial I/O

Six serial I/O channels via the P2 connector. Two channels are
equipped with clocks for synchronised operation with interfaces
that allow for RS422 or RS232.

Keyboard and Mouse

PS/2 compatible Keyboard and Mouse interface via the P2
connector.

Parallel I/O

Centronics style port via the P2 connector.

Floppy Disk Interface

MFM 1.44/2.88 Mbyte via P2 connector.

Counter/Timers

Eight 32-bit timers with a resolution of one bus clock (100 Mhz).

Reset/Abort switch

Front panel mounted

Operating Systems

LynxOS
VxWorks/Tornado
INTEGRITY

PCI Expansion

PCI through P0 via PMCPCI card.

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Содержание PMCGA1-101


















































































































Результаты поиска

Содержание PMCGA1-101

Отзывы:

Похожие инструкции для PMCGA1-101

Бренды по названию

Популярные бренды

Radstone PMCGA1-101, Руководство по эксплуатации продукта

Результаты поиска

Содержание PMCGA1-101

Отзывы:

Похожие инструкции для PMCGA1-101

Бренды по названию

Популярные бренды