background image

GENERAL INFORMATION

 

 

TG05A095.A0306

 

1

1. GENERAL INSTRUCTIONS 

 

1.1 General warnings 

  Professionally qualified personnel in accordance with current laws and standards and in line with 

the manufacturer’s instructions must install the appliance. To check for authorised qualified 
engineers please contact CORGI 01256-372400 

  The term professionally qualified personnel refers to persons possessing the appropriate technical 

competencies within the sector with regard to the installation and servicing of domestic and 
industrial central heating plants and domestic hot water production systems as provided for by 
current standards. 

  The commissioning of the boiler and any subsequent works carried out on the appliance must be 

effected by an appropriately qualified technician or an approved Radiant Helpline Service Centre. 

  The appliance must be used solely for the purpose for which it has been designed and 

manufactured: central heating and domestic hot water production. Any other use is deemed as 
improper and as such dangerous.  Under no circumstances will the manufacturer be held 
responsible for damage or injury to persons or animals caused by errors in the installation and/or 
use of the appliance, or through non-compliance with current local and national standards and/or 
the manufacturer’s instructions.

 

  The installation, operation and maintenance manual forms an integral and essential part of the 

product and must be kept near the appliance always. 

  This Manufacturer Installation and Maintenance manual must not be removed on completion of the 

installation; must be kept in a safe place and made available for future reference. This Manual must 
be left along with the Benchmark commissioning booklet with the boiler as Regulation 29 of the 
HSC Gas safety (installation and use) Regulations 1998

.

   

 

 

  The warnings contained in this chapter have been written for the appliance user, the installer and 

the service engineer. 

  The “operating instructions” chapter of this manual must be read carefully as it provides 

information on the operation and the operating limits of the appliance. 

  This appliance must be used exclusively in an un-vented central heating system. 

  After the removal of all the packaging, check that the appliance has not been damaged. In case of doubt, do not 

attempt to use the product but refer to the supplier. Packing materials (cardboard box, wooden crate, nails, 
staples, plastic bags, polystyrene, etc.) must not be left within reach of children in that these items represent a 
potential hazard and must be disposed of in a responsible manner. 

  Before carrying out any cleaning or maintenance operations, disconnect the appliance from the mains electricity 

supply by switching off at the main switch and/or any other isolating device. 

  Do not obstruct the air intake or heat dissipation grills. 

  Do not obstruct the openings of the air intake or flue ducts. 

  In the case of a fault and/or malfunction in the appliance, shut down the system. Do not interfere with or attempt 

any repairs. Call for professionally qualified technical assistance only. Radiant Helpline UK 0870 770 0414 

  Any warranty repairs to the appliance must be carried out exclusively by the manufacturer’s authorised service 

centre using original spare parts. Non-compliance with the above requirements may compromise the safety of 
the appliance and invalidate the warranty. In order to guarantee the efficiency of the appliance and its correct 
operation, it must be serviced regularly by professionally qualified personnel in line with the manufacturer’s 
instructions. 

  When the appliance is no longer required for use, any parts that may constitute potential sources of danger 

must be rendered harmless. 

  Only original accessories or optional extras (including electrical parts) must be used with the appliance.  

 

Содержание RKA 25

























































Отзывы: