manualshive.com logo in svg

Radiant RBC 24, Инструкция по установке, эксплуатации и обслуживанию, Страница: 49 / 68

Поделиться
Скачать
Radiant RBC 24 Скачать руководство пользователя страница 49

49

RBS 24 - RAD - ING - Manual - 1709.1_MIAB2013_R7

2 Codici 

di segnalazione 

anomalie_c

ombinata_aperta_MIAB2013_EN

2. MAINTENANCE  

SUPPOR

T

 C

ENTRE

CODE

FAULT

POSSIBLE CAUSE

SOLUTION

RESET

E18

I N S U F F I C I E N T 
CIRCULATION

EXCHANGER OBSTRUCTED;

CLEAN OR REPLACE THE EXCHANGER;

AUTOMATIC.

CIRCULATOR BROKEN OR 

DIRTY IMPELLER.

CLEAN THE IMPELLER OR REPLACE THE 

CIRCULATOR.

E21

GENERAL INTERNAL 
BOARD ERROR

INCORRECT SIGNAL 

RECOGNITION BY THE 

MODULATION BOARD 

MICRO-PROCESSOR.

IF THE MODULATION BOARD DOES NOT 

RESET THE ERROR AUTOMATICALLY, 

REPLACE IT.

AUTOMATIC.

E22

P A R A M E T E R S 
PROGRAMMING REQUEST

MICRO=PROCESSOR 

MEMORY LOSS.

PARAMETERS REPROGRAMMING.

MANUAL 

RESET 

(CUT OFF THE 

TENSION).

E31

REMOTE CONTROLLER 
INCOMPATIBLE

INDICATES THAT THE 

REMOTE CONTROLLER 

CONNECTED TO THE BOILER 

IS NOT COMPATIBLE WITH 

THE CIRCUIT BOARD

REPLACE IT WITH A COMPATIBLE 

MODEL.

AUTOMATIC.

E40

SUPPLY VOLTAGE

SUPPLY VOLTAGE OFF THE 

OPERATION RANGE (

d

160 

VOLTS).

CHECK THE POWER SUPPLY 

NETWORK (THE ERROR DEACTIVATES 

AUTOMATICALLY AS SOON AS THE 

SUPPLY VOLTAGE FALLS BACK WITHIN 

THE REQUESTED LIMITS).

AUTOMATIC.

E72

AIR PRESSURE SWITCH/
ELECTRIC FAN PRESSURE 
SWITCH CHECK UP ERROR

CONNECTION ERROR OF 

THE AIR PRESSURE SWITCH/

ELECTRIC FAN

AIR PRESSURE SWITCH 

CONTACT BLOCKED;

ELECTRIC FAN DEFECTIVE;

CHECK THE WIRING;

REPLACE THE AIR PRESSURE SWITCH;

REPLACE IT;

MANUAL RESET 

(PRESS THE RESET ‘

’ KEY).

Содержание RBC 24





































































Отзывы:

Нет отзывов