Radiant RBC 24 страница 61 Скачать руководство пользователя

Страница: 61 / 68

RBS 24 - RAD - ING - Manual - 1709.1_MIAB2013_R7

3 Codici

di segnalazione

anomalie_c

ombi_aperta_MIAB2013_EN

3. USE

USER

3.1.8. FAULT SIGNALLING CODES

The boiler might signal some faults by displaying a code. Below you have a list of the codes and of the
operations to be performed in order to unlock the boiler.

CODE

FAULT

INTERVENTION

E01

FLAME BLOCK

MAKE SURE THAT THE BOILER AND CONTACTOR GAS VALVES ARE OPEN.

PRESS THE RESET ‘

’ BUTTON ON THE CONTROL PANEL TO RESET THE FAULT,

AS SOON AS THE ERROR CODE DISAPPEARS FROM THE DISPLAY, THE BOILER

WILL START AUTOMATICALLY.

IF THE BLOCK PERSISTS CONTACT THE TECHNICAL SUPPORT CENTRE.

E02

SAFETY THERMOSTAT (95 °C)

CONTACT THE TECHNICAL SUPPORT CENTRE.

E03

FLUE SAFETY THERMOSTAT

CONTACT THE TECHNICAL SUPPORT CENTRE.

E04

WATER MISSING IN THE SYSTEM

IF THE SYSTEM PRESSURE IS BELOW 1.2 BAR, FILL THE SYSTEM AS DESCRIBED IN

CHAPTER “SYSTEM FILLING”.

IF THE BLOCK PERSISTS CONTACT THE TECHNICAL SUPPORT CENTRE.

E05

HEATING PROBE

CONTACT THE TECHNICAL SUPPORT CENTRE.

E06

DOMESTIC CIRCUIT PROBE

CONTACT THE TECHNICAL SUPPORT CENTRE.

E17

MODULATOR

CONTACT THE TECHNICAL SUPPORT CENTRE.

E18

INSUFFICIENT CIRCULATION

CONTACT THE TECHNICAL SUPPORT CENTRE.

E21

GENERAL INTERNAL BOARD ERROR

CUT OFF THE POWER SUPPLY FROM THE MAIN SWITCH AND THEN RESTORE

IT, AS SOON AS THE ERROR CODE DISAPPEARS, THE BOILER WILL RESTART

AUTOMATICALLY.

IF THE BLOCK PERSISTS CONTACT THE TECHNICAL SUPPORT CENTRE.

E22

PARAMETERS PROGRAMMING REQUEST

CUT OFF THE POWER SUPPLY FROM THE MAIN SWITCH AND THEN RESTORE

IT, AS SOON AS THE ERROR CODE DISAPPEARS, THE BOILER WILL RESTART

AUTOMATICALLY.

IF THE BLOCK PERSISTS CONTACT THE TECHNICAL SUPPORT CENTRE.

E31

REMOTE CONTROLLER INCOMPATIBLE

CONTACT THE TECHNICAL SUPPORT CENTRE.

E40

SUPPLY VOLTAGE

CONTACT THE TECHNICAL SUPPORT CENTRE.

Содержание RBC 24





































































Результаты поиска

Содержание RBC 24

Отзывы:

Похожие инструкции для RBC 24

Бренды по названию

Популярные бренды

Radiant RBC 24, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание RBC 24

Отзывы:

Похожие инструкции для RBC 24

Бренды по названию

Популярные бренды