Quincy QGB 20 Скачать руководство пользователя страница 18

Страница: 18 / 100

Section III - Installation

Pneumatic Circuit Breakers or Velocity

Fuses

Pneumatic safety devices are designed to

prevent hoses from whipping, which could

result in a serious or fatal accident.

The Occupational Safety and Health Act,

Section 926.303 Paragraph 7 published

in Code of Federal Regulations 29 CFR

920. (revised 07/0/982), states “all

hoses exceeding /2” inside diameter

shall have a safety device at the source of

supply or branch line to reduce pressure in

case of a hose failure.”

Guards

All mechanical action or motion is

hazardous in varying degrees and needs to

be guarded. Guarding shall comply with

OSHA Safety and Health Standards 29 CFR

90.29 in OSHA manual 2206 (revised

/07/978) and any state or local codes.

Warning!

Cabinet panels and drive guards must

be fastened in place before starting

the machine and never removed before

lock out/tag out of the main power

supply.

Manual Vent and Shutoff Valve

Install a manual valve to vent the

compressor and the compressor discharge

line to atmosphere. If the air receiver tank

services a single compressor, the manual

valve can be installed in the receiver.

When a manual shutoff valve (block valve)

is used, a manual valve should be installed

upstream from the valve, and a pressure

relief valve installed upstream from the

manual vent valve. These valves are

to be designed and installed to permit

maintenance to be performed in a safe

manner. Never substitute a check valve for

a manual shutoff valve (block valve) if the

purpose is to isolate the compressor from a

system for servicing.

Warning!

Relieve compressor and system air

pressure by opening the appropriate

manual relief valve prior to servicing.

Failure to relieve all system pressure

could result in death or serious injury

and property damage.

Quincy Compressor-QGB

™

Back to Table of Contents

Содержание QGB 20





































































































Результаты поиска

Содержание QGB 20

Отзывы:

Похожие инструкции для QGB 20

Бренды по названию

Популярные бренды

Quincy QGB 20, Инструкция по эксплуатации

Результаты поиска

Содержание QGB 20

Отзывы:

Похожие инструкции для QGB 20

Бренды по названию

Популярные бренды