Quincy QGB 20 Скачать руководство пользователя страница 47

Страница: 47 / 100

Section VI - Servicing

Belt Replacement

These instructions must be followed in

order to provide proper installation and

tensioning. Once belt replacement is

complete, perform drive system inspection

as outlined above.

) Lock out and tag out the electrical

power supply.

2) Remove panels and guards to gain

access to belt drive area.

3) Loosen Jam nut (#0).
4) Loosen spring nut (#9) until spring

(#3) is at free length (uncompressed).

5) Remove top hitch pin (#6).
6) Remove top clevis pin (#7). (Make

sure no spring force is exerted on

the clevis pin before removing, as

to prevent the adapter (#2) from

springing up).

7) Raise the motor platen to a sufficient

angle to allow the removal of the

used belts and enable the installation

of the new belts .

8) Lower the motor platen and allow the

weight to be supported by the belts.

Warning!

Keep body parts out from under the

motor platen during belt replacement

to avoid injury from falling motor

platen.

9) Re-install top clevis pin (#7).
0) Re-install top hitch pin (#6).
) Tighten spring nut (#9) and compress

spring (#3) until the proper belt

tension is achieved.

2) Check belt tension.
3) Tighten jam nut (#0) against spring

nut (#9).

4) Operate compressor to check

adjustment.

TOP

CLEvIS

(#7)

CLEvIS

ADAPTER

(#2)

INDICATOR

(#8)

SPRING

NuT

(#9)

jAM

NuT

(#10)

BOTTOM

CLEvIS

(#12)

TOP

HITCH

(#6)

CLEvIS

(#1)

SPRING

(#3)

SPRING

wASHER

(#4)

TENSIONER

ROD

(#5)

MOTOR

PLATE

TONGuE

(#11)

BOTTOM

COTTER

(#13)

Quincy Compressor-QGB

™

Back to Table of Contents

Содержание QGB 20





































































































Результаты поиска

Содержание QGB 20

Отзывы:

Похожие инструкции для QGB 20

Бренды по названию

Популярные бренды

Quincy QGB 20, Инструкция по эксплуатации

Результаты поиска

Содержание QGB 20

Отзывы:

Похожие инструкции для QGB 20

Бренды по названию

Популярные бренды