Quincy QGB 20 Скачать руководство пользователя страница 30

Страница: 30 / 100

Section V - Integrated Dryer (option)

Start-up & Operation

The non-cycling design of the refrigerated

dryer assures proper dew point control

at all load conditions. The refrigerant

compressor runs continuously when the

dryer is “ON”. All dryers are installed

with fan cycling switch. These fans will

cycle with respect to the load changes,

ambient temperature fluctuations, and the

cleanliness of the condenser. Standard

units are designed to operate under the

following conditions:

1) Inlet Air Temperature - 100°F design

120°F maximum

2) Inlet Air Pressure - 100 PSIG design

175 PSIG maximum

3) Ambient Air Temperature - 40°F

minimum 110°F maximum

notiCe!

At temperatures above the 100°F

design, refrigeration capacity will

decrease. Operating air pressures

below the 100 PSIG design will reduce

system capacity.

Start-up Procedure

Air dryers with three-phase power supply

are equipped with a compressor crankcase

heater. This heater must be energized by

closing the disconnect switch or circuit

breaker a minimum of 6 to 10 hours before

start-up. Power to the air dryer can be left

on to energize the crankcase heater for

the off-cycle, during evening or weekend

shutdowns.

Caution!

STARTING THE DRYER WITHOUT

ENERGIZING THE CRANKCASE

HEATER WILL CAUSE PREMATURE

FAILURES OF THE REFRIGERANT

COMPRESSOR. Failure to comply with

procedure of energizing crankcase

heater before start-up may void

warranty.

Operating Range & Control Settings

(R-134a refrigerant)

1)  Suction Pressure: 25 to 33 PSIG
2)  Discharge Pressure: 100 to 160 PSIG
3)  Low Pressure Switch: CUT OUT: 20

PSIG CUT IN: 45 PSIG

4) High Pressure Switch: 250 PSIG
5) Fan Control: CUT OUT: 110 PSIG

CUT IN: 150 PSIG

Shutdown Procedure

Turn the power switch to the OFF position.

Caution!

Contact factory before authorizing any

warranty refrigeration service on the air

dryer. Identify the dryer by model and

serial numbers when calling factory.

Quincy Compressor-QGB

™

Back to Table of Contents

Содержание QGB 20





































































































Результаты поиска

Содержание QGB 20

Отзывы:

Похожие инструкции для QGB 20

Бренды по названию

Популярные бренды

Quincy QGB 20, Инструкция по эксплуатации

Результаты поиска

Содержание QGB 20

Отзывы:

Похожие инструкции для QGB 20

Бренды по названию

Популярные бренды