background image

Section I - General Information

Royal Blue Warranty

Quincy Compressor®

Industrial Screw Products

QGB™ 20-60 HP - Rotary Screw Air Compressors

Variable Speed Drives (if applicable) -

 Five 

years (60 months) from date of start up (not 

to exceed 66 months from date of shipment), 

including parts & labor for the first year (12 

months), parts only for the remainder of 

the warranty period. Unit must be installed 

indoors in a well ventilated environment 

& a line reactor purchase (from Quincy 

Compressor) is required.

Remanufactured Airend - 

Twelve (12) months 

from date of shipment from the factory.

Parts -

 Ninety (90) days from date of Distributor 

sale  or  one  (1)  year  from  date  of  factory 

shipment.
With respect to products not manufactured by 

Seller,  Seller  will,  if  practical,  pass  along  the 

warranty of the original manufacturer.
The  terms  of  coverage  for  the  Royal  Blue 

Warranty are listed below. Failure to follow the 

terms will invalidate the Royal Blue Warranty.

AUTHORIZED START-UP REQUIRED:

A properly completed start-up report and the 

Royal Blue Warranty registration form must be 

submitted by an authorized Quincy distributor 

to the Quincy Compressor Bay Minette office 

within  thirty  (30)  days  of  start-up.  Start-up 

reports must be submitted on Q-Serv.

GENUINE PARTS AND FLUIDS

The  compressor  must  be  maintained  with 

QuinSyn-PG (8,000 hours maximum), QuinSyn-

XP (12,000 hours maximum), QuinSyn-Plus (8,000 

hours maximum) or QuinSyn-F fluid (4,000 hours 

maximum). Maximum fluid change intervals are 

noted per fluid. Actual fluid change interval is 

to be determined by fluid sampling report, not 

to exceed maximum fluid change interval. Fluid 

samples must be taken every 2,000 hours or as 

directed by the analysis report.
Only genuine Quincy Compressor maintenance 

and  replacement  parts  may  be  used  on  the 

compressor.

Seller warrants products of its own manufacture 

against defects in workmanship and materials 

under normal use and service, as follows:

QGB™  Packaged  Compressors  - 

Twelve  (12) 

months from date of start-up or twenty-four (24) 

months from date of shipment from the factory, 

whichever occurs first.

Airend on Packaged Compressors (for service 

at full-load pressure at or below 150 psig) -

 Ten 

years (120 months) from date of startup (not to 

exceed 126 months from date of shipment from 

the factory).

Airend on Packaged Compressors (for service 

at full-load pressure above 150 psig) - 

Twelve 

(12) months from date of start-up or twenty-four 

(24)  months  from  date  of  shipment  from  the 

factory, whichever occurs first.

Air/fluid Reservoir Tank - 

Five years (60 months) 

from date of start up (not to exceed 66 months 

from  date  of  shipment),  including  parts  and 

labor.  In  the  event  of  a  reservoir  tank  failure, 

the parts and labor coverage is limited to the 

reservoir  tank  itself  and  does  not  cover  the 

separator element(s) or loss of fluid.

Air and Fluid Heat Exchangers - 

Five years (60 

months) from date of start up (not to exceed 66 

months from date of shipment), including parts 

and labor for the first twelve (12) months, parts 

only after twelve (12) months. In the event of 

a  heat  exchanger  failure,  the  parts  and  labor 

coverage is limited to the heat exchanger itself 

and does not cover the loss of fluid.

Drive Motor - 

Five years (60 months) from date 

of start up (not to exceed 66 months from date 

of shipment), including parts and labor. Royal 

Blue warranty does not cover medium voltage 

(above 575 volt, 3 phase) motors. Before any 

motor repairs or replacements are performed, 

the  factory  must  be  contacted  at  the  time  of 

failure in order to approve any further action.

Drive Coupling Element - 

Five years (60 months) 

from date of start up (not to exceed 66 months 

from  date  of  shipment),  including  parts  and 

labor. (Machine must be installed and operated 

in accordance with the Operator’s Manual.)

Revised airend coverage (05/21/07).

Quincy Compressor-QGB

Back to Table of Contents

Содержание QGB 20





































































































Отзывы: