Quadratec Quadratop 12020-2000 Скачать руководство пользователя | Manualshive

Страница: 13 / 20

background image

13

STEP 4: INSTALLING ROPE ORGANIZER FOR RAFTERS (Side to Side)

A. Center one side of rope orginizer plate onto riser board and mark mounting hole location with pencil.

Drill two 5/32” mounting holes.

Rope Pulley Mounting Board

Rope Pulley Mounting Board

B. Assemble rope orginizer using plate and pulleys supplied in kit. Fasten to 2” x 6” riser board with with two

1/4” x 2 ½” lag bolts and 1/4” washers. Do not overtighten bolts. Rope orginizer pulleys will need to turn freely.

If overtightened hoist will not operate properly.

«
...
11
12
13
14
15
...
»

Содержание Quadratop 12020-2000





















Отзывы:

Нет отзывов

Похожие инструкции для Quadratop 12020-2000

Бренд: Ultrasonic Страницы: 16

ABICAR 1200 PRO

Бренд: Abicor Binzel Страницы: 64

Q-SYS Core 110f

Бренд: QSC Страницы: 2

Triton Barrier TL-2

Бренд: VALTIR Страницы: 28

Бренд: Vestil Страницы: 17

Synchro-Pulse CDT 450 CP38-3

Бренд: WELDING INDUSTRIES Страницы: 62

Бренд: Ergoswiss Страницы: 4

Бренд: ZKTeco Страницы: 41

Бренд: National Instruments Страницы: 16

ID ISC.ANT.U500/270

Бренд: Feig Electronic Страницы: 54

Бренд: Lincoln Electric Страницы: 35

Бренд: Jasic Страницы: 21

Бренд: Myson Страницы: 2

Бренд: Woodward Страницы: 32

Бренд: M-system Страницы: 10

Бренд: Advance acoustic Страницы: 31

SMART MATRIX WINDINGFEEDER

Бренд: btsr Страницы: 59

Бренд: GYS Страницы: 76

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды