Quadra-Fire 7100FP-BK-B Скачать руководство пользователя страница 1

Страница: 1 / 48

Installation and service of this fi replace should be

performed by qualifi ed personnel. Hearth & Home

Technologies recommends NFI certifi ed profes-

sionals, or technicians supervised by an

NFI certifi ed professional.

EPA CERTIFIED WOODBURNING

FIREPLACE

Fire Risk.

WARNING

For use with solid wood fuel only.

Other fuels may overﬁ re and generate poisonous

gases (i.e. carbon monoxide).

O-T L

Tested and

Listed by

Portland

Oregon USA

OMNI-Test Laboratories, Inc.

Model(s):

Installation Manual

Installation and Fireplace Setup

WARNING

HOT SURFACES

Glass and other surfaces are hot during

operation AND cool down.

Hot glass will cause burns.

•

DO NOT

touch glass until it is cooled

• NEVER allow children to touch glass

• Keep children away

• CAREFULLY SUPERVISE children in same room as

fi replace.

• Alert children and adults to hazards of high temperatures.

High temperatures may ignite clothing or other fl ammable

materials.

• Keep clothing, furniture, draperies and other fl ammable

materials away.

INSTALLER: Leave this manual with party responsible for use and operation.

OWNER: Retain this manual for future reference.

7100FP-BK-B

7100FP-GD-B

7100FP-NL-B

NOTICE:

DO NOT

discard this manual!

•

DO NOT

store or use gasoline or other fl am-

mable vapors and liquids in the vicinity of this

or any other appliance.

•

DO NOT

overfi re. Overfi ring will void your

warranty.

• Comply with all minimum clearances to com-

bustibles as specifi ed. Failure to comply may

cause house fi re.

WARNING: If the information in these

instructions is not followed exactly, a fi re

or explosion may result causing property

damage, personal injury, or death.

Pour demander un exemplaire

en français de ce Manuel

du propriétaire, visitez www.

heatnglo.com/translations.

Quadra-Fire • 7100 FP • 433-3610 Installation Manual • Rev G • 5/27/14

Содержание 7100FP-BK-B

















































Результаты поиска

Содержание 7100FP-BK-B

Отзывы:

Похожие инструкции для 7100FP-BK-B

Бренды по названию

Популярные бренды

Quadra-Fire 7100FP-BK-B, Руководство по установке

Результаты поиска

Содержание 7100FP-BK-B

Отзывы:

Похожие инструкции для 7100FP-BK-B

Бренды по названию

Популярные бренды