QTech QSW-6200-32T Скачать руководство пользователя страница 5

Страница: 5 / 56

QSW-6200

Series Switch Hardware Installation and Reference Guide

www.qtech.ru

particular time.



QSW-6200 series switch is a class A product. In a domestic environment, this product may cause radio

interference in which case the user may be required to take adequate measures.



Warning: Disconnect the power source prior to open case, and close case before restoring power.



Warning: Hazardous moving parts. Keep away from moving fan blades.



For DC input: Reinforce insulation or double insulation must be provided to isolate DC source from the AC mains

supply.



For DC input: A readily accessible disconnect device shall be incorporated in the building installation wiring.



For AC input: the socket-outlet shall be installed near the equipment and shall be easily accessible.



Because the device has several power supplies, disconnect all of them to switch off the device.



When installing the unit, always make the ground connection first and disconnect it last.



The device must be connected permanently to the protection ground before an operation. The cross sectional

area of protective ground conductor shall be at least 0.75 mm².

1.1 QSW-6200-32T

Technical Specifications

Model

QSW-6200-32T

Expansion Module

Slot

2 slots

Power Module

Slot



2 slots



AC input:

Rated voltage: 100V to 240V

Maximum voltage: 90V to 264V

Frequency: 50/60 Hz

Rated current per input: 2A



HVDC input:

Rated voltage: 120V to 340V

Maximum voltage: 110V to 380V

Rated current per input: 2A



DC input:

Rated voltage: -36V to -72V

Rated current per input: 3.15A

Содержание QSW-6200-32T

























































Результаты поиска

Содержание QSW-6200-32T

Отзывы:

Похожие инструкции для QSW-6200-32T

Бренды по названию

Популярные бренды

QTech QSW-6200-32T, Руководство по установке и справочное руководство по оборудованию

Результаты поиска

Содержание QSW-6200-32T

Отзывы:

Похожие инструкции для QSW-6200-32T

Бренды по названию

Популярные бренды