QTech QSW-6200-32T Скачать руководство пользователя страница 49

Страница: 49 / 56

QSW-6200

Series Switch Hardware Installation and Reference Guide

www.qtech.ru

For the detailed information during the arrester installation, please refer to Ethenet Port Arrester Hardware Installation

Guide, which contains the technical specification and the maintenance and installation of the arrester.

You may pay attention to the following conditions during the actual installation to avoid influencing the performance of the

Ethernet port arrester:



Reversed direction of the arrester installation. Yo

u shall connect the external network cable to the “IN” end and

connect the switch Ethernet port to the “OUT” end.



Poor arrester grounding. The length of the grounding line should be as short as possible to ensure that it is in

good contact with the switch grounding terminal. Use the multimeter to confirm the contact condition after the

grounding.



Incomplete arrester installation. If there is more than one port connected to the peer device on the switch, it

needs to install the arresters on all connection ports for the purpose of the lightning protection.

Содержание QSW-6200-32T

























































Результаты поиска

Содержание QSW-6200-32T

Отзывы:

Похожие инструкции для QSW-6200-32T

Бренды по названию

Популярные бренды

QTech QSW-6200-32T, Руководство по установке и справочное руководство по оборудованию

Результаты поиска

Содержание QSW-6200-32T

Отзывы:

Похожие инструкции для QSW-6200-32T

Бренды по названию

Популярные бренды