QTech QSW-6200-32T Скачать руководство пользователя страница 14

Страница: 14 / 56

QSW-6200

Series Switch Hardware Installation and Reference Guide

www.qtech.ru

System status LED

Status

Off

The switch is not receiving power.

Blinking green

(3 Hz)

The switch is being initialized with 3Hz blinking.

Continuous blinking indicates errors.

Blinking green

(10Hz)

Supports remote on/off to locate the switch.

Solid green

The switch is operational.

Solid yellow

Temperature alarm:

1. Temperature of inlet/outlet air exceeds the

normal operating temperature range.

2. The power supplies cannot support the whole

system.

Check the working environment of the switch and

power supplies immediately.

Solid red

The switch is faulty. For details, see the chapter

“Troubleshooting”.

Power status LED

PWR1/PWR2

Off

The power module is not in place or not receiving

power.

Solid green

The power module is connected and can supply

power.

Solid red

The redundant power is faulty or the AC power

cord is not connected.

MGMT port status

LED

MGMT

Off

The port is not connected.

Solid green

The port is connected at 1000 Mbps.

Blinking green

The port is receiving or transmitting traffic at

1000 Mbps.

Solid yellow

The port is connected at 10/100 Mbps.

Blinking yellow

The port is receiving or transmitting traffic at

10/100 Mbps.

10GE SFP+ port

status LED

49F-52F

Off

The port is not connected.

Solid green

The port is connected at 1/10 Gbps.

Blinking green

The port is receiving or transmitting traffic at 1/10

Содержание QSW-6200-32T

























































Результаты поиска

Содержание QSW-6200-32T

Отзывы:

Похожие инструкции для QSW-6200-32T

Бренды по названию

Популярные бренды

QTech QSW-6200-32T, Руководство по установке и справочное руководство по оборудованию

Результаты поиска

Содержание QSW-6200-32T

Отзывы:

Похожие инструкции для QSW-6200-32T

Бренды по названию

Популярные бренды