QTech QSW-6200-32T Скачать руководство пользователя страница 47

Страница: 47 / 56

QSW-6200

Series Switch Hardware Installation and Reference Guide

www.qtech.ru

Addition B Lightning Protection

Installing AC Power Arrester (lightning protection cable row)

The external lightning protection cable row shall be used on the AC power port to prevent the switch from being struck by

lightning when the AC power cable is introduced from the outdoor and directly connected to the power port of the switch.

The lightning protection cable row is fixed on the cabinet, operating table or the wall in the machine room using the line

buttons and screws.

Figure B-1 Schematic Diagram for the Power Arrester

The power arrester is not provided and the user shall purchase it to address the practical requirement.

Precautions for installation:



Make sure that the PE terminal of the power arrester has been well-grounded;



After connecting the switch AC power plug to the socket of the power arrester (lightning protection socket),

lightning protection function implements if the RUN LED is Green and the ALARM LED is OFF.



If the ALARM LED on the power arrester is Red, you shall check what the reason is, poor grounding connection

or the reversed connection of the Null and Live lines: Use the multimeter to check the polarity of the power socket

for the arrester when the LED is Red, if the N line is on the left and the L line is on the right, the arrester PE

terminal is not grounded; if the L line is on the left and the N line is on the right, the polarity of the arrester power

cable shall be reversed; if the LED is still Red, it is confirmed that the arrester PE terminal has not been

grounded.

Содержание QSW-6200-32T

























































Результаты поиска

Содержание QSW-6200-32T

Отзывы:

Похожие инструкции для QSW-6200-32T

Бренды по названию

Популярные бренды

QTech QSW-6200-32T, Руководство по установке и справочное руководство по оборудованию

Результаты поиска

Содержание QSW-6200-32T

Отзывы:

Похожие инструкции для QSW-6200-32T

Бренды по названию

Популярные бренды