QTech QSW-6200-32T Скачать руководство пользователя страница 19

Страница: 19 / 56

QSW-6200

Series Switch Hardware Installation and Reference Guide

www.qtech.ru

Solid green

The power module is in place and can supply

power.

Solid red

The redundant power is faulty or the AC power

cord is not connected.

MGMT port status

LED

MGMT

Off

The port is not connected.

Solid green

The port is connected at 1000 Mbps.

Blinking green

The port is receiving or transmitting traffic at

1000 Mbps.

Solid yellow

The port is connected at 10/100 Mbps.

Blinking yellow

The port is receiving or transmitting traffic at

10/100 Mbps.

10GE SFP+ port

status LED

29F-32F

Off

The port is not connected.

Solid green

The port is connected at 1/10 Gbps.

Blinking green

The port is receiving or transmitting traffic at 1/10

Gbps.

GE SFP port status

LED

1F-28F

Off

The port is not connected.

Solid green

The port is connected at 1000 Mbps.

Blinking green

The port is receiving or transmitting traffic at

1000 Mbps.

Solid yellow

The port is connected at 100 Mbps.

Blinking yellow

The port is receiving or transmitting traffic at 100

Mbps.

10/100/1000Base-T

auto-sensing

Ethernet port status

LED

1-8

Off

The port is not connected.

Solid green

The port is connected at 1000 Mbps.

Blinking green

The port is receiving or transmitting traffic at

1000 Mbps.

Solid yellow

The port is connected at 10/100 Mbps.

Blinking yellow

The port is receiving or transmitting traffic at

10/100 Mbps.

Содержание QSW-6200-32T

























































Результаты поиска

Содержание QSW-6200-32T

Отзывы:

Похожие инструкции для QSW-6200-32T

Бренды по названию

Популярные бренды

QTech QSW-6200-32T, Руководство по установке и справочное руководство по оборудованию

Результаты поиска

Содержание QSW-6200-32T

Отзывы:

Похожие инструкции для QSW-6200-32T

Бренды по названию

Популярные бренды