manualshive.com logo in svg

Q'STRAINT QLK-150, Руководство по установке, Страница: 11 / 36

Поделиться
Скачать
Q'STRAINT QLK-150 Скачать руководство пользователя страница 11

11

INSTALLATION INSTRUCTIONS

Order of Installation

Image

Location

Notes

Wheelchair Interface Bracket 

and V-Guide 

(Required for Driver Application)

Mark Location of QLK-150 

Wheelchair Docking System            

and Stabilizer 

(Required for Driver Application)

Connect the 3 Pin Wire Harness 

(Power, Ground and Ignition)

Test System Operation Before 

Installation

Routing Wires

Connect the 3 Pin Wire Harness 

(Power, Ground and Ignition)

Electronic Control Module (ECM)

Dash Control 

OPTIONAL 

Auxiliary Release Switch 

OPTIONAL

 

Manual Release Control 

QLK-150 Wheelchair Docking 

System

Stabilizer

OR

Advanced Stabilizer  

Attach to wheelchair

Choose best location for 

installation

Temporarily connect wires 

to disconnected main power 

source

Temporarily connect to wiring 

and harnesses then reconnect 

main power source

Choose best location for 

installation

Permanently connect to main 

power source

Behind Dash Panel

On the Dash Panel

Near the Wheelchair 

Occupant

Chosen location

Chosen location

Chosen location

Fitted Onto the 

QLK-150

Docking System

Varies depending on the wheelchair 

model

Center Wheelchair over Docking System 

and mark up the position of Docking 

System and Stabilizer

Disconnect main power source and 

make sure there are no open electrical 

connections

Make sure equipment is working properly 

before installation then disconnect main 

power source

Make sure wires and harnesses are free 

of moving components

Locations 

MUST

 be free of paint, 

corrosion and moisture

Avoid moving components and heat 

sources

If no lights illuminate when the ignition 

is turned on, 

DO NO

T use the QLK-150 

Wheelchair Docking System

The wheelchair occupant is able to 

release themselves from the Docking 

System

The wheelchair occupant or driver are 

able to manually release the wheelchair 

from the Docking System    

Drill the 6 holes

Required for driver application and 

strongly recommended for all other 

applications—reconnect main power 

source

Required for driver application and 

strongly recommended for all other 

applications 

(depending on wheelchair 

type)

—reconnect main power source

Содержание QLK-150





































Отзывы:

Нет отзывов