background image

 

 

WARRANTY 

 

Your  Ultrasonic  Processor  is  warranted  for  a  period  of  two  years

 

from  the  date  of 

shipment against defects in material and workmanship under normal use as described in 
this  instruction manual. During the  warranty  period,  the manufacturer  will,  at  its  option, 
as the exclusive remedy, either repair or replace without charge for material and labor, 
the  part(s)  which  prove  to  be  defective,  provided  the  unit  is  returned  to  us  properly 
packed with all transportation charges prepaid. 
 
Ultrasonic probes are guaranteed against defects for a period of one year from date of 
shipment. A defective probe will be replaced once without charge, if failure occurs within 
the warranty period. Wear resulting from cavitation erosion is a normal consequence of 
ultrasonic processing, and is not covered by this warranty. 
 
This warranty is in lieu of any other warranties, either express, implied, or statutory. The 
manufacturer  neither  assumes  nor  authorizes  any  person  to  assume  for  it  any  other 
obligations  or  liability  in  connection  with  the  sale  of  its  products.  The  manufacturer 
hereby  disclaims  any  warranty  of  either  merchantability  or  fitness  for  a  particular 
purpose. No person or company is authorized to change, modify, or amend the terms of 
this warranty in any manner whatsoever. Under no circumstances shall the manufacturer 
be  liable  to  the  purchaser  or  any  other  person  for  any  incidental  or  consequential 
damages  or  loss  of  goodwill,  production,  or  profit  resulting  from  any  malfunction  or 
failure of its product. 
 
This warranty does not apply to equipment that has been subject to unauthorized repair, 
misuse,  abuse,  negligence  or  accident.  Equipment  which,  shows  evidence  of  having 
been  used  in  violation  of  operating  instructions,  or  which  has  had  the  serial  number 
altered or removed, will be ineligible for service under this warranty. 
 
All  probes  are  manufactured  to  exacting  specifications  and  are  tuned  to  vibrate  at  a 
specific frequency. Using an out-of-tune probe will cause damage to the equipment and 
may  result  in  warranty  nullification.  The  manufacturer  assumes  no  responsibility  for 
probes  fabricated  by  another  party  or  for  consequential  damages  resulting  from  their 
usage. 
 
The aforementioned provisions do not extend the original warranty period of any product 
that has either been repaired or replaced by the manufacturer. 

 
 
 
 
 
 
 
 

one  year

2

Содержание CT2000































Отзывы: