Qiagen PyroMark Q24 MDx страница 43 Скачать руководство пользователя

Страница: 43 / 104

Operating Procedures

PyroMark Q24 MDx User Manual 01/2016

5-15

17.

While holding the tool over the PyroMark Q24 Plate,

close the vacuum switch on the tool (Off).

18.

Release the beads in the plate containing sequencing

primer, by shaking the tool gently from side to side.

19.

With the vacuum switch closed (Off), transfer the tool to

the trough containing high-purity water and agitate the
tool for 10 s.

20.

Wash the filter probes by lowering the probes into the
second trough of high-purity water and applying

vacuum. Flush the filter probes with 70 ml high-purity
water.

21.

Raise the tool to beyond 90° vertical for 5 s, to drain

liquid from the filter probes.

22.

Close the vacuum switch on the tool (Off) and place the

tool in the Parking (P) position.

23.

If more than one plate is prepared at once, refill the

troughs (step 2) and repeat the procedure from step 8.

24.

Turn off the vacuum pump.

25.

At the end of a working day, liquid waste and any

remaining solutions should be discarded and the
PyroMark Q24 MDx Vacuum Workstation should be

checked for dust and spillage, (see Section 5.6.2).

Содержание PyroMark Q24 MDx









































































































Результаты поиска

Содержание PyroMark Q24 MDx

Отзывы:

Похожие инструкции для PyroMark Q24 MDx

Бренды по названию

Популярные бренды

Qiagen PyroMark Q24 MDx, Руководство пользователя

Результаты поиска

Содержание PyroMark Q24 MDx

Отзывы:

Похожие инструкции для PyroMark Q24 MDx

Бренды по названию

Популярные бренды