Qiagen PyroMark Q24 MDx Скачать руководство пользователя страница 41

Страница: 41 / 104

Operating Procedures

PyroMark Q24 MDx User Manual 01/2016

5-13

Switch on the vacuum pump.

Apply vacuum to the tool by opening the vacuum switch.

Wash the filter probes by lowering the probes into high-

purity water. Flush the probes with 70 ml high-purity
water.
Ensure that the water is being transferred to the waste

container. If it is not, ensure the tubing  is connected
correctly and  is not  broken. Broken tubing should be
replaced (see Section  6.3.4).
Ensure that the waste filter is dry. If the filter is wet, it
should  be replaced (see Section  6.3.5).

Close the vacuum switch on the tool (Off) and place the

tool in the Parking position.

Refill trough 5 with 70 ml high-purity water.

Dilute the sequencing primer to 0.3 µM in Annealing

Buffer. Add 25 µl of the solution to each well of a
PyroMark Q24 Plate that is to be used.

Note

: Use one of the supplied PyroMark Q24 Plate

Holders as support when preparing and moving the

plate.

Содержание PyroMark Q24 MDx









































































































Результаты поиска

Содержание PyroMark Q24 MDx

Отзывы:

Бренды по названию

Популярные бренды

Qiagen PyroMark Q24 MDx, Руководство пользователя

Результаты поиска

Содержание PyroMark Q24 MDx

Отзывы:

Бренды по названию

Популярные бренды