Qiagen PyroMark Q24 MDx Скачать руководство пользователя страница 49

Страница: 49 / 104

Operating Procedures

PyroMark Q24 MDx User Manual 01/2016

5-21

Saving

The run data is transferred to the USB stick.

Do not remove the USB stick until the
instrument confirms that the run file has been
saved.

Finished

The run has been completed and the run data

have been transferred to the USB stick.

Pyrogram and warnings

The run name and selected well are displayed in the top left
corner. To select another well, use the



and



screen buttons.

Any instrument warnings are displayed below the Pyrogram

area (the three latest warnings are displayed). For suggested
actions, see Section 7.3.

Abort the run

To abort the run, press “Stop”.

5.5.5

After the run

When the instrument confirms that the run file has been
saved to the USB stick, press “Close”.

Remove the USB stick.

Open the instrument lid.

Open the cartridge gate and remove the reagent

cartridge by lifting it up and pulling it out.

Close the gate.

Open the plate-holding frame and remove the plate

from the heating block.

Close the plate-holding frame and the instrument lid.

Discard the plate.

If the reagent cartridge is to be reused, clean it according

to the instructions below.

10.

If this was the last run for the day, follow the instructions

in Section 5.6.

Содержание PyroMark Q24 MDx









































































































Результаты поиска

Содержание PyroMark Q24 MDx

Отзывы:

Бренды по названию

Популярные бренды

Qiagen PyroMark Q24 MDx, Руководство пользователя

Результаты поиска

Содержание PyroMark Q24 MDx

Отзывы:

Бренды по названию

Популярные бренды