Qiagen PyroMark Q24 MDx страница 19 Скачать руководство пользователя

Страница: 19 / 104

General Description

PyroMark Q24 MDx User Manual 01/2016

3-1

General Description

The PyroMark Q24 MDx uses proven real-time sequence-
based Pyrosequencing

technology for sequence-based

detection and quantification  in genetic analysis and
epigenetic methylation studies.  The system can analyze up to
24 samples  simultaneously.  An easy-to-use protocol  is used

to prepare samples.

3.1

PyroMark Q24 MDx definitions



PyroMark Q24 MDx: Instrument, software, and
installation



PyroMark Q24 MDx Instrument: Instrument only



PyroMark Q24 MDx Software: Software only



PyroMark Q24 MDx Vacuum Workstation: Vacuum

Workstation only



PyroMark Q24 MDx System: All of the above, plus any
PyroMark Kits

3.2

Pyrosequencing principle

Pyrosequencing uses sequencing by synthesis for accurate

and quantitative analysis of DNA sequences.
1.

A sequencing primer is hybridized to a single-stranded,

PCR-amplified DNA template.

The template is incubated with enzymes and substrates.

The first of four nucleotides is added to the reaction. If
the nucleotide is complementary to the base in the

template strand it will be incorporated into the DNA
strand by the DNA polymerase.

Each incorporation event is accompanied by release of

pyrophosphate (PPi) in an equimolar quantity to the

amount of nucleotide incorporated.

Содержание PyroMark Q24 MDx









































































































Результаты поиска

Содержание PyroMark Q24 MDx

Отзывы:

Похожие инструкции для PyroMark Q24 MDx

Бренды по названию

Популярные бренды

Qiagen PyroMark Q24 MDx, Руководство пользователя

Результаты поиска

Содержание PyroMark Q24 MDx

Отзывы:

Похожие инструкции для PyroMark Q24 MDx

Бренды по названию

Популярные бренды